Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F2317/F2317M-16a
Standard Specification for Design of Weight-Shift-Control Aircraft (Includes all amendments and changes 12/27/2016).
NORMA vydaná dňa 1.11.2016
Informácie o norme:
Označenie normy: ASTM F2317/F2317M-16a
Dátum vydania normy: 1.11.2016
Kód tovaru: NS-669616
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F2317/F2317M-16a :
This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified for: (1) proof of compliance including hang point and trimming setting; (2) general performance such as (a) stall speed in the landing configuration, (b) stall speed free of control limits, (c) minimum climb performance, (d) flutter, buffeting, and vibration, (e) turning flight and stalls, and (f) maximum sustainable speed in straight and level flight; (3) controllability and maneuverability such as general, longitudinal, and lateral control; and (4) longitudinal stability and pitch testing. Structural requirements specified include: (1) strength requirements, (2) fulfillment of design requirements, (3) safety factors, (4) design airspeeds, (5) flight loads, (6) pilot control loads, (7) ground loads including landing gear shock absorption, and (8) emergency landing loads. Design and construction requirements are specified for: (1) materials, (2) fabrication methods, (3) self-locking nuts, (4) protection of structure, (5) accessibility, (6) setup and breakdown, (7) control system evaluated by operation test, (8) mast (pylon) safety device, (9) cockpit design, and (10) markings and placards. Powerplant requirements including installation, fuel system, oil system, induction system, and fire prevention, as well as equipment requirements such as powerplant instruments, miscellaneous equipment, and lap belts and harnesses, are detailed. Operating limitations such as load distribution limits are also specified.
Keywords:
hang point, trimmer, weight-shift-control aircraft,, ICS Number Code 49.020 (Aircraft and space vehicles in general)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||
|
1.1 This specification covers the minimum airworthiness standards a manufacturer shall meet in the designing, testing, and labeling of weight-shift-control aircraft. 1.2 This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Note 1: This section is intended to preclude hinged surfaces
such as typically found on conventional airplanes such as rudders
and elevators. Flexible sail surfaces typically found on
weight-shift aircraft are not considered hinged surfaces for the
purposes of this specification.
1.3 Weight-shift-control aircraft means a powered aircraft with a framed pivoting wing and a fuselage (trike carriage) controllable only in pitch and roll by the pilot's ability to change the aircraft's center of gravity with respect to the wing. Flight control of the aircraft depends on the wing's ability to flexibly deform rather than the use of control surfaces. 1.4 This specification is organized and numbered in accordance with the bylaws established for Committee F37. The main sections are:
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. |
||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
