Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F2163-01(2008) 1.5.2008 náhľad

Doplňujúce informácie

ASTM F2163-01(2008)

Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring

Automaticky preložený názov:

Štandardné špecifikácie pre Ring, ložiská, vnútorná: pre ihlové ložisko s Drawn vonkajšom krúžku

NORMA vydaná dňa 1.5.2008

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 60.70 € Tlačené - 60.70 €
Dostupnosť	SKLADOM
Cena	60.70 € bez DPH
60.70 €

Informácie o norme:

Označenie normy: ASTM F2163-01(2008)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2008
Kód tovaru: NS-53040
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Valivá ložiska

Anotácia textu normy ASTM F2163-01(2008) :

Keywords:
drawn outer ring, inner ring, MS 17130 , needle roller bearing, Needle bearing, Needle roller bearing, Roller bearings, Ball/roller bearings--specifications, Drawn outer ring, Inner ring, ICS Number Code 21.100.20 (Rolling bearings)

Doplňujúce informácie

1. Scope

1.1 This specification covers inner rings for needle roller bearings with drawn outer rings.

1.2 The inner rings specified in this specification are intended for use on unhardened shafts in conjunction with open end needle roller bearings shown on Specification F 2162 and MS52141.

1.3 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.

1.4 The inner rings specified in this specification are not intended for use in flight-critical systems of aircraft.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Note 1—This specification contains many of the requirements of MS17130, which was originally developed by the Department of Defense and is currently maintained by the Defense Supply Center Richmond.

2. Referenced Documents

MIL-STD-130	Identification Marking of US Military Property Available from USA Information Systems, 1092 Laskin Rd., Ste. 208, Virginia Beach, VA 23451.
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
ASME B 46.1	Surface Texture Surface Roughness, Waviness, and Lay Available from Global Engineering Documents, 15 Inverness Way, East Englewood, CO 80112-5704, http://www.global.ihs.com.
STD 4	Tolerance Definitions and Gauging Practices For Ball and Roller Bearings Available from the American Bearing Manufacturers Association, 1200 19th St. NW, Ste. 300, Washington, DC 200362401.
ISO 5593	Rolling BearingsVocabulary Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
MS52141	Bearing, Roller, Needle: Drawn Outer Ring, Caged, Without Inner Ring, Open and Closed End, Standard Type
SAE J-404
SAE AHS
F2162-01(2016)	Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type