Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F2159-11

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Automaticky preložený názov:

Štandardné špecifikácie pre plastovou vložkou Kovanie Využitím Copper Crimp krúžok pre SDR9 sieťovaný polyetylén ( PEX ) rúrky a SDR9 polyetylénovej zo zvýšenej teplote ( PE - RT ) Tubing

NORMA vydaná dňa 15.4.2011

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 71.00 € Tlačené - 71.00 €
Dostupnosť	SKLADOM
Cena	71.00 € bez DPH
71.00 €

Informácie o norme:

Označenie normy: ASTM F2159-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.4.2011
Kód tovaru: NS-53028
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F2159-11 :

Keywords:

cold- and hot-water distribution, copper crimp rings, cross-linked polyethylene, plastic insert fittings, PE-RT, polyethylene of raised temperature, PEX, Crosslinked polyethylene (PEX) pipe/tube--specifications, Hot water supply/distribution systems--specifications, Plastic pipe/tubing/fittings--specifications, Cold water supply/distribution systems--specifications, Copper crimp rings--specifications, ICS Number Code 23.040.45 (Plastic fittings)

Doplňujúce informácie

1. Scope

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes
(³/₈, ½, and ¾ and 1) of cross-linked polyethylene (PEX) plastic tubing an polyethylene of raised temperature (PE-RT) tubing. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.

1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following is an index of the appendix in this specification:

GO/NO-GO Crimp Gauges

Appendix X1

1.4 The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents

F2769-24	Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems
B 1.20.1	Pipe Threads General Purpose Inch Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
ANSI/NSF Standard No. 14	for Plastic Piping Components and Related Materials Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
ANSI/NSF Standard No. 61	for Drinking Water System Components-Health Effects
F2623-24e1	Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications (Includes all amendments and changes 3/8/2024).
F1498-08(2020)	Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
F876-24	Standard Specification for Crosslinked Polyethylene (PEX) Tubing
F412-23	Standard Terminology Relating to Plastic Piping Systems
D6394-21a	Standard Classification System for and Basis for Specification for Sulfone Plastics (SP) (Includes all amendments and changes 5/13/2021).
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
F1807-23	Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
D618-21	Standard Practice for Conditioning Plastics for Testing
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.