Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F2145-01 10.10.2001 náhľad

Doplňujúce informácie

ASTM F2145-01

Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing

Automaticky preložený názov:

Štandardné špecifikácie pre polyamid 11 ( PA 11 ) mechanickým zariadením na užívanie na Outside Diameter ovládanú polyamid 11 rúrok a rúrky

NORMA vydaná dňa 10.10.2001

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 62.50 € Tlačené - 62.50 €
Dostupnosť	SKLADOM
Cena	62.50 € bez DPH
62.50 €

Informácie o norme:

Označenie normy: ASTM F2145-01
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.10.2001
Kód tovaru: NS-52979
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F2145-01 :

Keywords:

gas, mechanical saddle fitting, plastic mechanical fitting, Polyamide 11 pipe, rotation test, temperature cycling test, ICS Number Code 23.040.45 (Plastic fittings)

Doplňujúce informácie

1. Scope

1.1 This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA 11) pipe, nominal 2 pipe size (IPS), and smaller complying with Specification D 2513. In addition, it specifies general requirements of the material from which these fittings are made.

1.2 The test methods described in this specification are not intended to be used as routine quality tests.

1.3 This specification covers the types of mechanical fittings covered in 3.2.1.

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

2. Referenced Documents

PPI TR-4	PPI Listing of Hydrostatic Design Bases (HDB), Pressure Design Bases (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825, Irving, TX 75062, http://www.plasticpipe.org.
ASME B31.8	Gas Transmission and Distribution Piping Systems Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
F2945-18(2023)	Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
F2785-21	Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
F1588-96(2019)	Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
F412-23	Standard Terminology Relating to Plastic Piping Systems
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D2513-20	Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D638-22	Standard Test Method for Tensile Properties of Plastics
CFR, Title 49, Part 192	Transportation of Natural and Other Gas By Pipeline: Minimum Federal Safety Standards Available from Superintendent of Documents, U.S. Government Printing Office, Washington D.C. 20402.Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.