Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F1909-98(2020)
Standard Specification for Preformed Open-Cell Sponge Rubber Pail and Drum Gaskets
NORMA vydaná dňa 1.1.2020
Informácie o norme:
Označenie normy: ASTM F1909-98(2020)
Dátum vydania normy: 1.1.2020
Kód tovaru: NS-982071
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F1909-98(2020) :
This specification covers preformed open-cell sponge rubber gaskets, for use in new or reconditioned pails or drums, of the following classes: Class A and Class B, each divided into Grade 1, Grade 2, and Grade 3. Cellular sponge rubber gaskets shall be made by incorporating a blowing agent into the compound, such as sodium bicarbonate, that gives off a gas which expands the mass during the vulcanization process, and shall be manufactured from natural rubber, synthetic rubber, or rubber-like materials, together with added compounding ingredients. Unless otherwise specified, gasket sponge rubber shall have a natural skin on both the top and bottom surfaces. Cellular rubber shall conform to the prescribed requirements as to physical properties such as (1) compression at deflection, (2) change in volume upon oil immersion, (3) change in compression value after heat aging, (4) compression set, and (5) color (tan or black). The following test methods shall be used: (1) compression deflection test, (2) oil immersion test, (3) heat oven aging test, and (4) compression set test under constant deflection. The formula for calculating the compression set is given. The requirements for sampling, test specimens and slabs, and measurements of test specimen such as width and thickness are detailed as well. The location from which standard test specimens are to be cut when testing standard test slabs or commercial flat sheets and the four-cavity frame for standard test slabs of cellular rubbers are illustrated.
Keywords:
gaskets, rubber, sponge,, ICS Number Code 83.140.50 (Seals)
Doplňujúce informácie
| 1. Scope | ||||||||||||||
|
1.1 This specification covers preformed open–cell sponge rubber gaskets of the following classes for use in new or reconditioned pails or drums. 1.1.1 Class A—Non–Oil Resistant. 1.1.2 Class B—Oil Resistant. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 The following safety hazards caveat pertains only to Section 10, General Test Methods. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: 1.4 This international standard was
developed in accordance with internationally recognized principles
on standardization established in the Decision on Principles for
the Development of International Standards, Guides and
Recommendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
|
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
