Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F1871-02e1

Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation (Withdrawn 2011) (Includes all amendments And changes 12/31/2010).

Automaticky preložený názov:

Štandardné špecifikácie pre skladané / tvoril Poly ( vinylchlorid ) Type Pipe A pre existujúce kanalizácie a Conduit rehabilitácie ( Withdrawn 2011 )

NORMA vydaná dňa 10.9.2002

Jazyk
Prevedenie	Online zabezpečené PDF - 72.20 € Tlačené - 72.20 €
Dostupnosť	SKLADOM
Cena	72.20 € bez DPH
72.20 €

Informácie o norme:

Označenie normy: ASTM F1871-02e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.9.2002
Kód tovaru: NS-51903
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM F1871-02e1 :

Keywords:

installation, underground, plastic pipe, thermoplastic, poly (vinyl chloride) (PVC) plastic pipe, rehabilitation, trenchless technology, ICS Number Code 23.040.20 (Plastic pipes), 83.080.20 (Thermoplastic materials)

Doplňujúce informácie

1. Scope

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, and a form of marking for folded/formed poly (vinyl chloride) (PVC) pipe for existing sewer and conduit rehabilitation.

1.2 Pipe produced to this specification is for use in non-pressure sewer and conduit rehabilitation where the folded PVC pipe is installed into and then expanded to provide a close fit to the wall of the original conduit, forming a new structural pipe-within-a-pipe.

Note 1—For installation procedures refer to Practice F 1867.

1.3 This specification includes pipe made only from materials specified in Section 6. This specification does not include pipe manufactured from reprocessed, recycled, or reclaimed PVC.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information only.

1.5 The following precautionary statement pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6 There is no similar or equivalent ISO Standard.

2. Referenced Documents

MIL-STD-129	Marking for Shipment and Storage
D618-21	Standard Practice for Conditioning Plastics for Testing
D2152-23	Standard Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D1784-20	Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D648-18	Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D638-22	Standard Test Method for Tensile Properties of Plastics
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
F1867-22	Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation
F1057-21	Standard Practice for Estimating the Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat Reversion Technique
F412-23	Standard Terminology Relating to Plastic Piping Systems
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.