Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determining Ink or Coating Adhesion on Flexible Substrates for a Membrane Switch or Printed Electronic Device (Withdrawn 2024)
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie atrament alebo priľnavosti povlaku na Pružné podklady pre prepínač membrány alebo Vytlačené elektronickým zariadením
NORMA vydaná dňa 1.6.2015
Označenie normy: ASTM F1842-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2015
Kód tovaru: NS-611391
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
adhesion, tape, adhesion test method´crosscut, adhesion test method´cross-hatch, adhesion test method´tape, coatings, inks, membrane switch, printed electronic device,, ICS Number Code 31.220.20 (Switches)
Significance and Use | ||
5.1 If the ink or coating is to fulfill its function, it must adhere to the substrate. Substrates and their surface preparation have a significant effect on the adhesion of inks or coatings. Therefore, a method of evaluating adhesion of inks or coatings to different substrates or surface treatments, or of different inks or coatings to the same substrate and surface treatment, is useful to the industry. 5.2 The limitations of all adhesion methods and the specific limitation of this test method to lower levels of adhesion should be recognized before using it. The intra– and inter–laboratory precision of this test method is under evaluation. 5.3 Printing area to be tested should be a solid area large enough to include the entire cross hatch pattern. |
||
1. Scope | ||
1.1 This test method is based on existing Test Method D3359, with modifications to make it suitable for flexible substrates, printed electronic devices and membrane switches. 1.2 Despite the problems associated with a tape test on plastic substrates, it is our belief that this is still one of the best ways to test ink and coating for adhesion for membrane switch or printed electronic device applications. In writing this test method we are addressing several of the objections to the test method that could affect its precision and repeatability on plastic substrates. 1.3 These test methods cover whether the adhesion of coating or ink to a substrate is at an acceptable level. They do not distinguish between higher levels of adhesion, for which more sophisticated methods of measurement may be required. Note 1: It should be recognized that differences in
adherability of the ink or coating surface can affect the results
obtained with inks or coatings having the same inherent
adhesion.
1.4 In multi–coat systems adhesion failure may occur between coats, so that the adhesion of the coating system to the substrate is not determined. 1.5 This test method is specifically designed for measuring adhesion of inks and coatings (films) that have a thickness of 5 mil (125 microns) or less, on plastics such as polyester and polycarbonate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||
2. Referenced Documents | ||
|
Historická
1.12.2007
Historická
1.6.2014
Historická
1.1.2014
Historická
1.6.2015
Historická
1.6.2015
Historická
1.1.2014
Posledná aktualizácia: 2024-04-28 (Počet položiek: 2 896 137)
© Copyright 2024 NORMSERVIS s.r.o.