Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F1837M-97(2012)e1 1.10.2012 náhľad

Doplňujúce informácie

ASTM F1837M-97(2012)e1

Standard Specification for Heat-Shrink Cable Entry Seals (Metric) (Includes all amendments And changes 10/25/2018).

Automaticky preložený názov:

Štandardné špecifikácie pre zmršťovacie Vstup kábla Seals (metrické)

NORMA vydaná dňa 1.10.2012

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.20 € Tlačené - 70.20 €
Dostupnosť	SKLADOM
Cena	70.20 € bez DPH
70.20 €

Informácie o norme:

Označenie normy: ASTM F1837M-97(2012)e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2012
Kód tovaru: NS-51765
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Pryžové a plastové izolační materiály

Anotácia textu normy ASTM F1837M-97(2012)e1 :

Keywords:

cable-entry seal, cable penetrator, cable termination, cross-linked polyolefin heat-shrinkable tubing, electrical insulation, heat-shrinkable tubing, ICS Number Code 29.035.20 (Plastic and rubber insulating materials)

Doplňujúce informácie

1. Scope

1.1 This specification covers the general requirements for heat-shrink cable entry seals. Cable entry seals are intended for making electrical cable penetrations into connection boxes, bulkheads, or other enclosures. These devices are suitable for both thin wall enclosures up to 5 mm (³/₁₆ in.) thick and thick-wall enclosures of 5 mm to 19 mm (³/₁₆ in. to ³/₄ in.) thick.

1.2 Cable entry seals shall have factory-applied adhesive that provides the seal to wire and cable jackets.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

2. Referenced Documents

D149-20	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D747-10	Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam (Withdrawn 2019)
D635-22	Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
D570-22	Standard Test Method for Water Absorption of Plastics
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D257-14(2021)e1	Standard Test Methods for DC Resistance or Conductance of Insulating Materials (Includes all amendments and changes 5/6/2021).
D4572-21	Standard Test Method for Rubber Chemicals—Wet Sieve Analysis of Sulfur
D3149-06	Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation
IEC 68-2-6	Environmental Testing-Part 2: Tests-Test FC: Vibration (Sinusoidal) Sixth Edition Available from International Electrotechnical Commission (IEC), 3, rue de Varembe, Case Postale 131, CH-1211, Geneva 20, Switzerland.
D2671-21	Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D2863-23	Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)
NEMA 250	Enclosures for Electrical Equipment (1000 Volts Max)
ASME B1.1	Unified Inch Screw Threads (UN and UNR Thread Form) Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
D4732-13(2020)	Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable