Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM F1667-15

Standard Specification for Driven Fasteners: Nails, Spikes, and Staples

Automaticky preložený názov:

Štandardné špecifikácie pre Driven Spojovacie : Klince, hroty , a Staples

NORMA vydaná dňa 1.9.2015

Jazyk
Prevedenie	Online zabezpečené PDF - 115.60 € Tlačené - 115.60 €
Dostupnosť	SKLADOM
Cena	115.60 € bez DPH
115.60 €

Informácie o norme:

Označenie normy: ASTM F1667-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2015
Kód tovaru: NS-618478
Počet strán: 47
Približná hmotnosť: 141 g (0.31 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Mechanické spojovací součásti obecně

Anotácia textu normy ASTM F1667-15 :

Keywords:

diameter, driven fasteners, head, length, nails, point, spikes, staples,, ICS Number Code 21.060.01 (Fasteners in general)

Doplňujúce informácie


1. Scope
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65. ^† Editorially corrected in March 2012. L	=	length, in.,
H	=	head diameter, in.,
TL	=	length of threaded shank, in.,
max	=	maximum acceptable value (not subject to tolerances),
min	=	minimum acceptable value (not subject to tolerances),
D	=	shank diameter, in.,
T1	=	crest diameter, in., and
P	=	pitch, or spacing of threads, in.

length, in.,

head diameter, in.,

length of threaded shank, in.,

max

maximum acceptable value (not subject to tolerances),

min

minimum acceptable value (not subject to tolerances),

shank diameter, in.,

crest diameter, in., and

pitch, or spacing of threads, in.

Dimensions and Tolerances for Gages of Flat Top Crown Staples

10 Gage

12 Gage

14 Gage

15 Gage

16 Gage

18 Gage

Nominal

.1250

.1400

.0935

.1120

.0735

.0855

.0673

.073

.0563

.064

.038

.050

Maximum

.1290

.1440

.0975

.1160

.0775

.0895

.0731

.076

.0626

.068

.0415

.0532

Minimum

.1210

.1360

.0895

.1080

.0695

.0815

.0615

.070

.0500

.060

.0345

.0468

Tolerance

.0040

.0058

.003

.0063

.004

.0035

.0032

1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

F680-20	Standard Test Methods for Nails
F1575-17	Standard Test Method for Determining Bending Yield Moment of Nails
F592-84(2001)	Standard Terminology of Collated and Cohered Fasteners and Their Application Tools
A153/A153M-23	Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
A510M-08	Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel [Metric] (Withdrawn 2011)
A641/A641M-19	Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
F547-22	Standard Terminology of Nails for Use with Wood and Wood-Base Materials

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.