Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F1487-21
Standard Consumer Safety Performance Specification for Playground Equipment for Public Use
NORMA vydaná dňa 1.5.2021
Informácie o norme:
Označenie normy: ASTM F1487-21
Dátum vydania normy: 1.5.2021
Kód tovaru: NS-1024079
Počet strán: 83
Približná hmotnosť: 280 g (0.62 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F1487-21 :
Keywords:
consumer safety, playground equipment, public use,, ICS Number Code 97.200.40 (Playgrounds)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This consumer safety performance specification provides safety and performance standards for various types of public playground equipment and dimensional requirements for their clearance and use zones. Its purpose is to reduce life-threatening and debilitating injuries. 1.2?The range of users encompassed by this consumer safety performance specification is the 5th percentile 2-year-old through the 95th percentile 12-year-old. 1.3?Home playground equipment, toys, amusement rides, sports equipment, fitness equipment intended for users over the age of 12, public use play equipment for children 6 to 24 months, and soft contained play equipment are not included in this specification. 1.4?Products or materials (site furnishings) that are installed outside the equipment use zone, such as benches, tables, independent shade structures, and borders used to contain protective surfacing, are not considered playground equipment and are not included in this specification. 1.5 This specification does not address accessibility, except as it pertains to safety issues not covered in the DOJ 2010 Standard for Accessible Design. 1.6?This consumer safety performance specification includes the following sections:
1.6.1?The requirements in this specification are designed to mitigate the hazards typically presented by various types of equipment. New equipment may not specifically fit into the designated types listed in the specification; however, the designer or manufacturer, or both, shall use professional judgment to perform and document a hazard analysis and follow appropriate requirements to mitigate the hazards. Note 1:?See Appendix X1
at the end of this standard to find more information on how one
might conduct such an assessment as stated in this
section.
1.7?General Measures, Tolerances, and Conversions:? 1.7.1?The general tolerances for this specification (unless otherwise specified) are as follows:
These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used. 1.7.2?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only. 1.7.3?The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 0.45359 kg. 1.7.4?See Annex A1 for figures referenced throughout this specification. 1.8?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
