Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F1430/F1430M-15 1.4.2015 náhľad

Doplňujúce informácie

ASTM F1430/F1430M-15

Standard Test Method for Acoustic Emission Testing of Insulated and Non-Insulated Aerial Personnel Devices with Supplemental Load Handling Attachments

Automaticky preložený názov:

Štandardná skúšobná metóda pre akustické emisie testovanie izolovaných a neizolovaných Aerial Personálne zariadení s Company Manipulátory Prílohy

NORMA vydaná dňa 1.4.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 77.10 € Tlačené - 77.10 €
Dostupnosť	SKLADOM
Cena	77.10 € bez DPH
77.10 €

Informácie o norme:

Označenie normy: ASTM F1430/F1430M-15
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2015
Kód tovaru: NS-588538
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Akustická měření a snižování hluku obecně

Anotácia textu normy ASTM F1430/F1430M-15 :

Keywords:
acoustic, aerial devices, emission, equipment,, ICS Number Code 17.140.01 (Acoustic measurements and noise abatement in general)

Doplňujúce informácie

Significance and Use

5.1 This test method provides a means of evaluating acoustic emissions generated by the rapid release of energy from localized sources within an APD under controlled loading. The resultant energy releases occur during intentional application of a controlled predetermined load. These energy releases can be monitored and interpreted by qualified individuals.

5.2 This test method permits testing of the major components of an aerial device under controlled loading. This test method utilizes objective criteria for evaluation and may be discontinued at any time to investigate a particular area of concern or prevent a fault from continuing to ultimate failure.

5.3 This test method provides a means of detecting acoustic emissions that may be defects or irregularities, or both, affecting the structural integrity or intended use of the aerial device.

5.4 Sources of acoustic emission found with this test method shall be evaluated by either more refined acoustic emission test methods or other nondestructive techniques (visual, liquid penetrant, radiography, ultrasonics, magnetic particle, etc.). Other nondestructive tests may be required to locate defects present in APDs.

5.5 Defective areas found in aerial devices by this test method should be repaired and retested as appropriate. Repair procedure recommendations are outside the scope of this test method.

1. Scope

1.1 This test method describes a procedure for acoustic emission (AE) testing of aerial personnel devices (APDs) with supplemental load handling attachments.

1.1.1 Equipment Covered—This test method covers the following types of vehicle-mounted aerial personnel devices with supplemental load handling attachments:

1.1.1.1 Extensible-boom APDs,

1.1.1.2 Articulating-boom APDs, and

1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.

1.1.2 Equipment Not Covered—This test method does not cover any of the following equipment:

1.1.2.1 Aerial personnel devices without supplemental load handling attachments,

1.1.2.2 Digger-derricks with platform,

1.1.2.3 Cranes with platform, and

1.1.2.4 Aerial devices with load-lifting capabilities located anywhere other than adjacent to the platform.

Note 1: This test method is not intended to be a stand-alone NDT method for the verification of the structural integrity of an aerial device. Other NDT methods should be used to supplement the results.

1.2 The AE test method is used to detect and area-locate emission sources. Verification of emission sources may require the use of other nondestructive test (NDT) methods, such as radiography, ultrasonics, magnetic particle, liquid penetrant, and visual inspection. (1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E164-19	Standard Practice for Contact Ultrasonic Testing of Weldments
E569-07	Standard Practice for Acoustic Emission Monitoring of Structures During Controlled Stimulation
E114-20	Standard Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing
ASNT? SNT-TC-1A	Recommended Practice for Personnel Qualification and Certification in Nondestructive Testing Available from American Society for Nondestructive Testing (ASNT), P.O. Box 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.
F2174-02(2023)	Standard Practice for Verifying Acoustic Emission Sensor Response
E750-15(2020)	Standard Practice for Characterizing Acoustic Emission Instrumentation
E94-04	Standard Guide for Radiographic Examination
E650-97	Standard Guide for Mounting Piezoelectric Acoustic Emission Sensors
F914-03	Standard Test Method for Acoustic Emission for Insulated and Non-Insulated Aerial Personnel Devices Without Supplemental Load Handling Attachments
E976-15(2021)	Standard Guide for Determining the Reproducibility of Acoustic Emission Sensor Response
E1316-24	Standard Terminology for Nondestructive Examinations
E1417/E1417M-21e1	Standard Practice for Liquid Penetrant Testing (Includes all amendments and changes 11/25/2021).
E1444/E1444M-22a	Standard Practice for Magnetic Particle Testing for Aerospace (Includes all amendments and changes 7/11/2022).
ANSI? A92.2	Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.