Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F1394-92(2012) 1.7.2012 náhľad

Doplňujúce informácie

ASTM F1394-92(2012)

Standard Test Method for Determination of Particle Contribution from Gas Distribution System Valves

Automaticky preložený názov:

Štandardná skúšobná metóda pre stanovenie častíc Príspevok z plynovej distribučnej sústavy ventily

NORMA vydaná dňa 1.7.2012

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 100.70 € Tlačené - 100.70 €
Dostupnosť	SKLADOM
Cena	100.70 € bez DPH
100.70 €

Informácie o norme:

Označenie normy: ASTM F1394-92(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2012
Kód tovaru: NS-50144
Počet strán: 27
Približná hmotnosť: 81 g (0.18 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Kulové a kuželovité ventily
Přímé uzavírací ventily

Anotácia textu normy ASTM F1394-92(2012) :

Keywords:
condensation nucleus center, contamination, gas distribution, gas distribution valves, isokinetic sampling, nitrogen, particle contamination, particle counter, particles, semiconductor processing, ICS Number Code 23.060.20 (Ball and plug valves), 23.060.10 (Globe valves)

Doplňujúce informácie


Significance and Use
4.1 The purpose of this test method is to define a procedure for testing components intended for installation into a high-purity gas distribution system. Application of this test method is expected to yield comparable data among components tested for the purposes of qualification for this installation. 4.2 Background Testing—This test method uses background testing to ensure that the system is not contributing particles above a low, acceptable level. This ensures that counts seen are from the test device, not from a contaminated system. The techniques used to obtain background counts do not produce conditions identical to the conditions existing when a test device is in place. It is recommended that the control products be run periodically to see that they give consistent results. These control products should be the lowest particle release products. They will be additional proof that the system is not contributing excess particles during the static, dynamic, or impact portions of the test. 4.3 This test method can be used for testing lengths of tubing. The flow criteria will be identical to that indicated for valves. A tubing test would only include the static background, the impact background, and the static and impact portions of the method. A dynamic portion could be added by actuating the upstream pneumatic valve (PV1), thus creating a flow surge to the test length of tubing.

1. Scope
1.1 This test method covers gas distribution system components intended for installation into a high-purity gas distribution system. 1.1.1 This test method describes a procedure designed to draw statistically significant comparisons of particulate generation performance of valves tested under aggressive conditions. 1.1.2 This test method is not intended as a methodology for monitoring on-going particle performance once a particular valve has been tested. 1.2 This test method utilizes a condensation nucleus counter (CNC) applied to in-line gas valves typically used in semiconductor applications. It applies to automatic and manual valves of various types (such as diaphragms or bellows), 6.3 through 12.7-mm (¹/₄ through ¹/₂-in.) size. For applications of this test method to larger valves, see the table in the appendix. 1.2.1 Valves larger than 12.7 mm (¹/₂ in.) can be tested by this methodology. The test stand must be sized accordingly. Components larger than 12.7 mm (¹/₂ in.) should be tested while maintaining a Reynolds number of 20 000 to 21 000. This is the Reynolds number for 12.7-mm (¹/₂-in.) components tested at a velocity of 30.5 m/s (100 ft/s). 1.3 Limitations: 1.3.1 This test method is applicable to total particle count greater than the minimum detection limit (MDL) of the condensation nucleus particle counter and does not consider classifying data into various size ranges. 1.3.1.1 It is questionable whether significant data can be generated from nondynamic components (such as fittings and short lengths of tubing) to compare, with statistical significance, to the data generated from the spool piece. For this reason, this test method cannot reliably support comparisons between these types of components. 1.3.1.2 If detection or classification of particles, or both, in the size range of laser particle counter (LPC) technology is of interest, an LPC can be utilized for testing components. Flow rates, test times, sampling apparatus, and data analysis outlined in this test method do not apply for use with an LPC. Because of these variations, data from CNCs are not comparable to data from LPCs. 1.3.2 This test method specifies flow and mechanical stress conditions in excess of those considered typical. These conditions should not exceed those recommended by the manufacturer. Actual performance under normal operating conditions may vary. 1.3.3 The test method is limited to nitrogen or clean dry air. Performance with other gases may vary. 1.3.4 This test method is intended for use by operators who understand the use of the apparatus at a level equivalent to six months of experience. 1.3.5 The appropriate particle counter manufacturer's operating and maintenance manuals should be consulted when using this test method. 1.4 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
FED-STD-209D	Federal Standard Clean Room and Work Station Requirements, Controlled Environment Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.