Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM F1342/F1342M-05(2022)
Standard Test Method for Protective Clothing Material Resistance to Puncture
NORMA vydaná dňa 1.2.2022
Informácie o norme:
Označenie normy: ASTM F1342/F1342M-05(2022)
Dátum vydania normy: 1.2.2022
Kód tovaru: NS-1049089
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM F1342/F1342M-05(2022) :
Keywords:
protective clothing materials, puncture, puncture resistance,, ICS Number Code 13.340.10 (Protective clothing)
Doplňujúce informácie
| Significance and Use | ||||
|
5.1?This test method evaluates puncture resistance of protective clothing materials which may include plastics or elastomeric films, coated fabrics, flexible materials, laminates, or textile materials. 5.2?This test method is not intended to measure puncture resistance of all types of punctures encountered using protective clothing material. This test method involves a procedure where a puncture probe of specified dimensions is used for puncturing specimens. 5.3?This test method evaluates puncture resistance of protective clothing materials, specifically for puncture forced on specimens perpendicular to material surface. There is no supporting structure under the material specimen. 5.4?Evaluation of puncture resistance for snag-type puncture should be performed in accordance with Test Method D2582. |
||||
| 1. Scope | ||||
|
1.1?This test method determines the puncture resistance of a protective clothing material specimen by measuring the force required to cause a pointed puncture probe to penetrate through the specimen. This test method describes three protocols that may be used: Method A, Method B, and Method C. 1.1.1?Method A requires the use of Probe A only. The probe used for testing shall be recorded in the test report. 1.1.1.1?Probe A may be used to measure puncture resistance for the following types of materials: (1)?Elastomeric materials, (2)?Textiles, and (3)?Coated materials. 1.1.2?Method B requires the use of Probe B. The probe used for testing shall be recorded in the test report. 1.1.2.1?Probe B may be used to measure puncture resistance for the following types of materials: (1)?Textiles. (2)?Coated materials. Note 1:?Probe B is not suited for measuring the puncture
resistance of unsupported elastomeric materials.
1.2?The values stated in SI units are to be regarded as the standard. The values in inch-pound units in brackets are for information purposes only. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
| 2. Referenced Documents | ||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
