Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM F1178-11(2015) 1.10.2015 náhľad

Doplňujúce informácie

ASTM F1178-11(2015)

Standard Specification for Performance of Enameling System, Baking, Metal Joiner Work and Furniture

Automaticky preložený názov:

Štandardné špecifikácie pre výkon smaltovanie systému , pečenie, Metal Stolárske práce a nábytok

NORMA vydaná dňa 1.10.2015

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.40 € Tlačené - 70.40 €
Dostupnosť	SKLADOM
Cena	70.40 € bez DPH
70.40 €

Informácie o norme:

Označenie normy: ASTM F1178-11(2015)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2015
Kód tovaru: NS-618101
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Povrchová úprava a povlakování obecně

Anotácia textu normy ASTM F1178-11(2015) :

Keywords:
baking finish, baking primer, enamel, fabricated metal products, joiner work, marine, marine furniture, metal painting, ship ,, ICS Number Code 25.220.01 (Surface treatment and coating in general)

Doplňujúce informácie

1. Scope

1.1 This specification covers the performance of a baking primer and enamel on metal for use on fabricated metal products, including marine furniture and joiner work.

1.2 The values stated in inch-pound units are to be regarded as standard. The metric (SI) units, given in parentheses, are for information only.

1.3 Painting facilities shall comply with all applicable Federal and State regulations regarding emissions and waste disposal.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D3363-22	Standard Test Method for Film Hardness by Pencil Test
AISC Wire and Sheet Metal Gages	Equivalent Thickness in Decimals of an Inch, U.S. Standard Gauge (USSG) for Uncoated Hot and Cold Rolled Sheets and Galvanized Sheet Gage (GSG) for Hot-Dipped Zinc Coated Sheets
D1186-01	Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006)
D1400-00	Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006)
B117-19	Standard Practice for Operating Salt Spray (Fog) Apparatus
A1008/A1008M-23e1	Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable (Includes all amendments and changes 12/29/2023).
B209-14	Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
D522-93a(2001)	Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
D3359-23	Standard Test Methods for Rating Adhesion by Tape Test
A653/A653M-23	Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process