Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing (Includes all amendments And changes 11/8/2022).
NORMA vydaná dňa 15.11.2016
Označenie normy: ASTM F1055-16a
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.11.2016
Kód tovaru: NS-673316
Počet strán: 14
Približná hmotnosť: 42 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
crosslinked polyethylene, electrofusion, fittings, joining, polyethylene, PEX,, ICS Number Code 23.040.20 (Plastic pipes)
1. Scope | ||||||||||||||||||||||||||||||||||||||
1.1 This specification covers electrofusion polyethylene fittings for use with outside diameter-controlled polyethylene pipe, covered by Specifications D2513, D2737, D3035, F714, F2623, F2769 and crosslinked polyethylene (PEX), covered by Specifications F876 and F2788/F2788M. Requirements for materials, workmanship, and testing performance are included. All requirements for joining PE electrofusion fittings to PE pipe shall also apply to joining PE electrofusion fittings to PEX pipe. Where applicable in this specification “pipe” shall mean “pipe” or “tubing.” 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazards caveat pertains
only to the test method portion, Section 9, of this specification:
Standard Specification for Crosslinked
Polyethylene (PEX) Tubing Standard Specification for Polyethylene
(PE) Plastic Pipe (DR-PR) Based on Outside Diameter Standard Terminology Relating to Plastic
Piping Systems Standard Specification for Polyethylene
Plastics Pipe and Fittings Materials Standard Specification for Polyethylene
(PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter Standard Specification for Polyethylene
(PE) Plastic Tubing Standard Specification for Polyethylene
(PE) Gas Pressure Pipe, Tubing, and Fittings Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) ISO 13954 Plastics pipe and fittings Peel
decohesion test for polyethylene (PE) electrofusion assemblies of
nominal diameter greater than or equal to 90 mm PPI TR-4 PPI TR-3 Standard Specification for Polyethylene
of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and
Distribution Systems Standard Specification for Metric and
Inch-sized Crosslinked Polyethylene (PEX) Pipe Standard Specification for Polyethylene
of Raised Temperature (PE-RT) Systems for Non-Potable Water
Applications (Includes all amendments and changes 3/8/2024). Standard Practice for Qualification of
Polyethylene Saddle-Fused Joints Standard Test Method for Notch Tensile
Test to Measure the Resistance to Slow Crack Growth of Polyethylene
Pipes and Resins Standard Test Method for Resistance to
Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and
Fittings Standard Test Method for Time-to-Failure
of Plastic Pipe Under Constant Internal Pressure Standard Test Method for Tensile
Properties of Plastics |
Posledná aktualizácia: 2024-04-19 (Počet položiek: 2 860 954)
© Copyright 2024 NORMSERVIS s.r.o.