Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM E292-09e1

Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials (Withdrawn 2018) (Includes all amendments And changes 5/1/2018).

Automaticky preložený názov:

Štandardné skúšobné metódy pre Vyhotovenie Time-pre-ruptúry Notch Ťažné skúšky materiálov

NORMA vydaná dňa 1.4.2009

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 76.10 € Tlačené - 76.10 €
Dostupnosť	SKLADOM
Cena	76.10 € bez DPH
76.10 €

Informácie o norme:

Označenie normy: ASTM E292-09e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2009
Kód tovaru: NS-46265
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Mechanické zkoušení kovů

Anotácia textu normy ASTM E292-09e1 :

Keywords:

axiality, bending strain, bending stress, elongation, final notch cross-sectional area, gage length, kt factor, loading, major diameter, minor diameter, notch cross-sectional area, notch root radius, notch rupture strength, stress, stress-rupture, temperature, thermocouple, Metals and metallic materials, Notches, Rupture/rupture strength, Strength, Thickness, ICS Number Code 77.040.10 (Mechanical testing of metals)

Doplňujúce informácie

Significance and Use

Rupture life of notched specimens is an indication of the ability of a material to deform locally without cracking under multi-axial stress conditions, thereby redistributing stresses around a stress concentrator.

The notch test is used principally as a qualitative tool in comparing the suitability of materials for designs that will contain deliberate or accidental stress concentrators.

1. Scope

1.1 These test methods cover the determination of the time for rupture of notched specimens under conditions of constant load and temperature. These test methods also includes the essential requirements for testing equipment.

1.2 The values stated in inch-pound units are to be regarded as the standard. The units in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

A453/A453M-17	Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels
E4-21	Standard Practices for Force Calibration and Verification of Testing Machines
E1012-19	Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
E220-19	Standard Test Method for Calibration of Thermocouples By Comparison Techniques
E691-23	Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E633-21a	Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing (Includes all amendments and changes 2/2/2022).
E177-20	Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
MIL-STD-120	Gage Inspection Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
E139-11(2018)	Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
E6-23a	Standard Terminology Relating to Methods of Mechanical Testing (Includes all amendments and changes 3/29/2023).
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
E74-18e1	Standard Practices for Calibration and Verification for Force-Measuring Instruments (Includes all amendments and changes 5/1/2019).