Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM E2133-03(2020)
Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface
NORMA vydaná dňa 1.11.2020
Informácie o norme:
Označenie normy: ASTM E2133-03(2020)
Dátum vydania normy: 1.11.2020
Kód tovaru: NS-1010164
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM E2133-03(2020) :
Keywords:
profiling device, rolling inclinometer, transverse and longitudinal profiles,, ICS Number Code 93.080.20 (Road construction materials)
Doplňujúce informácie
| Significance and Use | ||||||||||||
|
5.1 This test method establishes procedures for collecting elevation and distance data of longitudinal and transverse profiles on a traveled surface. 5.2 Results of this test are used primarily to: 5.2.1 Evaluate the roughness of traveled surfaces, using any of several roughness indices shown in Table 1. Equations required for calculations of various indexes are contained in references shown in Table 1. Note 1: When this test is used to evaluate the compliance of a
new pavement surface with contract roughness specifications, the
timeliness of the test in relation to the date of the surface's
installation is of critical importance. Since most portland cement
concrete surfaces will change shape within a few days after
installation—due to changes in thermal and moisture gradients which
cause curling at joints and cracks and slab edges—for contractor
quality control only, it may be desirable to gather profile data
within 72 h after pavement installation.
5.2.2 Investigate the effect of different construction methods on resulting pavement surface roughness. 5.2.3 Investigate the curvature of (5.2.4 Identify the locations in need of corrective grinding. 5.2.5 Measure rut depth using computer simulation in accordance with Test Method E1703/E1703M. |
||||||||||||
| 1. Scope | ||||||||||||
|
1.1 This test method describes the measurement of transverse and longitudinal surface profiles on paved road, bridge, and airport surfaces using a rolling inclinometer traveling at walking speed. 1.2 It is designed to (1) quantify the roughness of new pavements and bridge decks; (2) investigate the effect of various construction methods on surface roughness; (3) determine the location for corrective grinding; and (1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
