Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM E2092-13

Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis

Automaticky preložený názov:

Štandardná skúšobná metóda pre skreslenie Teplota vo trojbodovom ohýbaní termomechanická analýza

NORMA vydaná dňa 1.9.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 80.10 € Tlačené - 80.10 €
Dostupnosť	SKLADOM
Cena	80.10 € bez DPH
80.10 €

Informácie o norme:

Označenie normy: ASTM E2092-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2013
Kód tovaru: NS-44262
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Plastické hmoty obecně

Anotácia textu normy ASTM E2092-13 :

Keywords:

deflection, deflection temperature under load, heat distortion temperature, strain, stress, temperature, thermomechanical analysis (TMA), ICS Number Code 83.080.01 (Plastics in general)

Doplňujúce informácie

Significance and Use

5.1 Data obtained by this test method shall not be used to predict the behavior of materials at elevated temperatures except in applications in which the conditions of time, temperature, method of loading, and stress are similar to those specified in the test.

5.2 This standard is particularly suited for quality control and development work. The data are not intended for use in design or predicting endurance at elevated temperatures.

1. Scope

1.1 This test method describes the determination of the temperature at which the specific modulus of a test specimen is realized by deflection in three-point bending. This temperature is identified as the distortion temperature. The distortion temperature is that temperature at which a test specimen of defined geometry deforms to a level of strain under applied stress of 0.455 MPa (66 psi) (Method A) and 1.82 MPa (264 psi) (Method B) equivalent to those used in Test Method D648. The test may be performed over the range of temperature from ambient to 300°C.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

1.4 There is no ISO standard equivalent to this test method.

2. Referenced Documents

E2206-21	Standard Test Method for Force Calibration of Thermomechanical Analyzers
E2113-23	Standard Test Method for Length Change Calibration of Thermomechanical Analyzers
E1363-23	Standard Test Method for Temperature Calibration of Thermomechanical Analyzers
E1142-23b	Standard Terminology Relating to Thermophysical Properties (Includes all amendments and changes 10/5/2023).
D648-18	Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
E473-23b	Standard Terminology Relating to Thermal Analysis and Rheology (Includes all amendments and changes 10/5/2023).