Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM E1795-20a

Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings (Includes all amendments and changes 12/17/2020).

NORMA vydaná dňa 1.11.2020

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 65.50 € PDF + redline - ihneď - 78.60 € Tlačené - 65.50 € Tlač + redline - 78.60 €
Dostupnosť	SKLADOM
Cena	65.50 € bez DPH
65.50 €

Informácie o norme:

Označenie normy: ASTM E1795-20a
Dátum vydania normy: 1.11.2020
Kód tovaru: NS-1013218
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Nátěrové hmoty, barvy a laky

Anotácia textu normy ASTM E1795-20a :

This specification covers minimum material performance requirements and laboratory test procedures for nonreinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Three types of nonreinforced liquid coating encapsulation products are presented: type I - encapsulation products intended for interior use, type II - encapsulation products intended for exterior use, and type III - encapsulation products intended for either interior or exterior use. The impact resistance, adhesion, dry abrasion resistance, water vapour transmission, water and chemical resistance, surface burning characteristics, and volatile organic compound content shall be tested to meet the requirements prescribed. Weathering, aging, scrub resistance, mildew resistance, paintability/repairability, flexibility, and tensile properties shall be tested to meet the requirements prescribed.

Keywords:

abatement, encapsulant, encapsulation, lead, leaded paint, liquid coating, liquid coating encapsulation product, non-reinforced liquid coating encapsulation product,, ICS Number Code 87.040 (Paints and varnishes)

Doplňujúce informácie

1. Scope

1.1?This specification covers minimum material performance requirements and laboratory test procedures for non-reinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are:

1.1.1?Impact resistance,

1.1.2?Adhesion,

1.1.3?Dry abrasion resistance,

1.1.4?Water vapor transmission,

1.1.5?Water and chemical resistance,

1.1.6?Surface burning characteristics,

1.1.7?Volatile organic compound (VOC) content,

1.1.8?Weathering,

1.1.9?Aging,

1.1.10?Scrub resistance,

1.1.11?Mildew resistance,

1.1.12?Paintability/repairability,

1.1.13?Flexibility, and

1.1.14?Tensile properties.

1.2?This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796.

1.3?This specification does not cover the use of corrosion-inhibiting primers prior to encapsulation products on either industrial steel structures or on residential coated metal surfaces. Types of Direct-To-Metal (DTM) primers in conjunction with lead paint encapsulants has not been investigated. Use of primers to yield substrates acceptable to receive an encapsulant, and to inhibit future corrosion of encapsulated substrates, should be evaluated by trial applications at each specific project.

1.4?This specification applies to any non-reinforced liquid applied product that relies primarily on adhesion for attachment to the surface. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead.

1.5?The results of the test methods included in this specification will not necessarily predict field performance.

1.6?The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D4708-24	Standard Practice for Preparation of Uniform Free Films of Organic Coatings
E84-23d	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
D7091-22	Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
E1605-22	Standard Terminology Relating to Lead in Buildings
D4414-95(2020)	Standard Practice for Measurement of Wet Film Thickness by Notch Gages
E2239-20	Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities
G154-23	Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials
E1796-20	Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings
E1797-12(2017)e1	Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings (Includes all amendments and changes 5/16/2019).
2012	Preparation of Tin Panels
3011	Condition in Container
D2486-17	Standard Test Methods for Scrub Resistance of Wall Paints
D2794-93(2024)	Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D3273-21	Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
D3274-09(2021)	Standard Test Method for Evaluating Degree of Surface Disfigurement of Paint Films by Fungal or Algal Growth, or Soil and Dirt Accumulation
D3359-23	Standard Test Methods for Rating Adhesion by Tape Test
D3891-23	Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products
D3924-16(2019)	Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials
D3925-02(2022)	Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings
D3960-05(2018)	Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
D4060-19	Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
D4214-23	Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
D16-24	Standard Terminology for Paint, Related Coatings, Materials, and Applications
D2370-16(2021)	Standard Test Method for Tensile Properties of Organic Coatings
D522-93a(2001)	Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
D823-18(2022)	Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels
D1005-95(2020)	Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D1212-91(2020)	Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings
D1308-20	Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Coating Systems
D1475-13(2020)	Standard Test Method for Density of Liquid Coatings, Inks, and Related Products
D1653-13(2021)	Standard Test Methods for Water Vapor Transmission of Organic Coating Films

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.