Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Collection of Settled Dust Samples Using Wipe Sampling Methods for Subsequent Lead Determination
Automaticky preložený názov:
Štandardná prax pre zber usadený prach vzoriek prostredníctvom utrite metódami odberu vzoriek pre následné Lead stanovenie
NORMA vydaná dňa 1.10.2010
Označenie normy: ASTM E1728-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2010
Kód tovaru: NS-42798
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
lead, sample collection, settled dust, wipe, Wipe sampling methods, Atomic absorption spectrometry (AAS), Dust wipe samples, FAAS (flame atomic absorption spectrometry), Field testing--soil, Graphite furnace atomic absorption spectrometry (GFAAS), ICP-AES (inductively-coupled plasma atomic emission spectrometry), Lead screening testing, Sample collection, Settled dust, Soil, Soil sampling, ICS Number Code 13.080.05 (Examination of soil in general)
Significance and Use | ||||||||||||||||||
This practice is intended for the collection of settled dust samples in and around buildings and related structures for the subsequent determination of lead content in a manner consistent with that described in the HUD Guidelines and 40 CFR 745.63. The practice is meant for use in the collection of settled dust samples that are of interest in clearance, hazard assessment, risk assessment, and other purposes. Use of different pressures applied to the sampled surface along with the use of different wiping patterns contribute to collection variability. Thus, the sampling result can vary between operators performing collection from identical surfaces as a result of collection variables. Collection for any group of sampling locations at a given sampling site is best when limited to a single operator. This practice is recommended for the collection of settled dust samples from hard, relatively smooth, nonporous surfaces. This practice is less effective for collecting settled dust samples from surfaces with substantial texture such as rough concrete, brickwork, textured ceilings, and soft fibrous surfaces such as upholstery and carpeting. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 This practice covers the collection of settled dust on surfaces using the wipe sampling method. These samples are collected in a manner that will permit subsequent extraction and determination of lead using laboratory analysis techniques such as atomic spectrometry or electroanalysis. 1.2 This practice does not address the sampling design criteria (that is, sampling plan which includes the number and location of samples) that are used for clearance, lead hazard evaluation, risk assessment, and other purposes. To provide for valid conclusions, sufficient numbers of samples should be obtained as directed by a sampling plan. 1.3 This practice contains notes that are explanatory and are not part of the mandatory requirements of this practice. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.5.2010
Historická
1.7.2013
Historická
1.8.2013
Historická
15.10.2012
Historická
15.1.2013
Historická
1.11.2006
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.