Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
Automaticky preložený názov:
Štandardná skúšobná metóda pre plošné horľavosti materiálov Použitím sálavého tepla zdroj energie
NORMA vydaná dňa 15.5.2013
Označenie normy: ASTM E162-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.5.2013
Kód tovaru: NS-42402
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
beta factor, fire-test-response standard, flame spread factor, radiant panel index, heat evolution factor, radiant heat energy, radiant panel, surface flame spread, surface flammability, ICS Number Code 13.220.50 (Fire-resistance of building materials and elements)
Significance and Use | ||||||||||||||
5.1 This test method provides a laboratory test procedure for measuring and comparing the surface flammability of materials when exposed to a prescribed level of radiant heat energy. It is intended for use in measurements of the surface flammability of materials exposed to fire. The test is conducted using small specimens that are representative, to the extent possible, of the material or assembly being evaluated. (Example: in terms of their thickness, layering, and any potential substrate.) 5.2 The rate at which flames will travel along surfaces depends upon the physical and thermal properties of the material, product or assembly under test, the specimen mounting method and orientation, the type and level of fire or heat exposure, the availability of air, and properties of the surrounding enclosure.4 5.3 In this procedure, the specimens are subjected to one or more specific sets of laboratory fire test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure. 5.4 If the test results obtained by this test method are to be considered as part of an overall assessment of fire hazard in a building or structure, then the example criteria, concepts and procedures incorporated into Guide E1546 shall be taken into consideration. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use as a basis of ratings for building code purposes (see 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section 7.
|
ISO13943
|
|
|
Standard Specification for Flat Fiber-Cement Sheets (Includes all amendments and changes 10/10/2023).
|
|
Standard Terminology of Fire Standards
|
|
Standard Guide for Development of Fire-Hazard-Assessment Standards
|
|
Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
|
|
Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source
|
|
Standard Specification for Fiber-Cement Interior Substrate Sheets |
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.