Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM E1155-20
Standard Test Method for Determining FF Floor Flatness and FL Floor Levelness Numbers
NORMA vydaná dňa 1.7.2020
Informácie o norme:
Označenie normy: ASTM E1155-20
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2020
Kód tovaru: NS-1003599
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM E1155-20 :
Keywords:
Ff, FF Flatness, Fl, FL Levelness, floor, floor profile, floor profilometer, F-Number,, ICS Number Code 91.060.30 (Ceilings. Floors. Stairs)
Doplňujúce informácie
| Significance and Use | ||||
|
5.1 This test method provides statistical (and graphical) information concerning floor surface profiles. 5.2 Results of this test method are used primarily to: 5.2.1 Establish compliance of randomly trafficked floor surfaces with specified FF Flatness and FL Levelness tolerances, 5.2.2 Evaluate the effect of different construction methods on resulting floor surface flatness and levelness, and 5.2.3 Investigate the curling and deflection of floor surfaces. 5.3 Results of this test method shall not be used to enforce contract flatness and levelness tolerances on those floor installations primarily intended to support the operation of fixed-path vehicle systems (for example, narrow aisle warehouse floors). Note 2: When the traffic patterns across a floor are random,
(as is generally the case) evaluation of the floor's FF Flatness and FL Levelness will necessarily
involve a random sampling of the surface, since all of the infinite
potential profiles to be seen by the traffic can not possibly be
measured. In those instances when the traffic across a floor will
be confined to specific paths, however, the requirement for random
sampling is eliminated, since the floor can indeed be inspected
exactly as it will be seen by all of the traffic. In these special
cases, rather than inferring the condition of the traffic paths
from a random sample, it is far more useful to measure each of the
traffic paths directly using continuous recording floor
profilometer configured to run exactly in the traffic wheel paths.
Such direct simulation measurements eliminate the inherent
uncertainties of statistical sampling and provide profile
information immediately applicable to the correction of the surface
in way of the future traffic.
|
||||
| 1. Scope | ||||
|
1.1 This test method covers a quantitative method of measuring floor surface profiles to obtain estimates of the floor's characteristic FF Flatness and FL Levelness Face Floor Profile Numbers (F-Numbers) using the inch-pound system of units. Note 1: A complete metric companion to Test Method
E1155 has been developed,
Test Method E1155M;
therefore, no metric equivalents are shown in this test
method.
1.2 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
| 2. Referenced Documents | ||||
|
Doporučujeme:
