Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM E1025-18

Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiography

NORMA vydaná dňa 1.2.2018

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 66.40 € PDF + redline - ihneď - 79.70 € Tlačené - 66.40 € Tlač + redline - 79.70 €
Dostupnosť	SKLADOM
Cena	66.40 € bez DPH
66.40 €

Informácie o norme:

Označenie normy: ASTM E1025-18
Dátum vydania normy: 1.2.2018
Kód tovaru: NS-809785
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Nedestruktivní zkoušení

Anotácia textu normy ASTM E1025-18 :

This practice covers the design, material grouping classification, and manufacture of hole-type image quality indicators (IQI) used to indicate the quality of X-ray and gamma-ray radiologic images.

Keywords:

density, image quality level, IQI, radiologic, radiology, X-ray and gamma radiation,, ICS Number Code 19.100 (Non-destructive testing)

Doplňujúce informácie

1. Scope

1.1 This practice2 covers the design, material grouping classification, and manufacture of hole-type image quality indicators (IQI) used to indicate the quality of radiologic images.

1.2 This practice is applicable to X-ray and gamma-ray radiology.

1.3 The values stated in inch-pound units are to be regarded as standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

MIL-I-24768	Insulation, Plastics, Laminated, Thermosetting; General Specification for Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
E746-23	Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems below 4 MeV
E2662-15(2022)	Standard Practice for Radiographic Examination of Flat Panel Composites and Sandwich Core Materials Used in Aerospace Applications
E1316-24	Standard Terminology for Nondestructive Examinations
B139/B139M-12(2017)	Standard Specification for Phosphor Bronze Rod, Bar, and Shapes
E747-18	Standard Practice for Design, Manufacture and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology
B166-19	Standard Specification for Nickel-Chromium-Aluminum Alloy, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Rod, Bar, and Wire
B164-03(2019)	Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
B150/B150M-19	Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
E1735-19	Standard Practice for Determining Relative Image Quality Response of Industrial Radiographic Imaging Systems from 4 to 25 MeV

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.