Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Calculated Cetane Index of Distillate Fuels
Automaticky preložený názov:
Štandardná skúšobná metóda pre Vypočítaná cetánový index destilátu palív
NORMA vydaná dňa 1.12.2006
Označenie normy: ASTM D976-06
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2006
Kód tovaru: NS-40000
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
cetane, cetane index, diesel fuel, ICS Number Code 75.160.20 (Liquid fuels)
Significance and Use | ||||||||||||||||
The Calculated Cetane Index is one tool available for estimating ASTM cetane number where a test engine is not available for determining this property. It may be employed for approximating cetane number where the quantity of sample is too small for an engine rating. In cases where the cetane number of a fuel has been initially established, the index is useful as a cetane number check on subsequent samples of that fuel, provided its source and mode of manufacture remain unchanged. Test Method D 4737 may also be used to approximate the ASTM cetane number of diesel fuels. 3.2.1 Procedure A of Test Method D 4737 was developed as a result of a larger degree of offset between Test Method D 976 Cetane Index and the results of Test Method D 613 over the entire range of the correlation. Generally, it has been found that use of Test Method D 4737 results in less offset than use of Test Method D 976, but there can be specific cases where this is not true. 3.2.2 Procedure A of Test Method D 4737 is recommended to estimate the cetane number of diesel fuels with sulfur contents above 500 ppm or No. 1–D diesel fuels. 3.2.3 Procedure B of Test Method D 4737 is recommended to estimate the cetane number of No. 2–D diesel fuels with sulfur contents at or below 500 ppm. Calculated Cetane Index, as described in Test Method D 976–80, is recognized by the United States EPA as an alternative method to meet the U.S. Federal Diesel aromatics limit for diesel fuels containing less than 500 ppm sulfur. The equation for Calculated Cetane Index in Test Method D 976–80 and in this version (D 976–06) of the test method are the same. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method covers the Calculated Cetane Index formula, which represents a means for directly estimating the ASTM cetane number of distillate fuels from API gravity and mid-boiling point. The index value, as computed from the formula, is termed the Calculated Cetane Index. 1.2 The Calculated Cetane Index is not an optional method for expressing ASTM cetane number. It is a supplementary tool to estimate cetane number when used with due regard for its limitations. 1.3 The Calculated Cetane Index formula is particularly applicable to straight-run fuels, catalytically cracked stocks, and blends of the two. Note 1This test method is temporarily retained because the proposal to the U.S. EPA to control diesel fuel aromatics concentrations via a 40 Calculated Cetane Index minimum is based on the correlation between Test Method D 976 and aromatics concentration. Test Method D 4737 is the preferred method as estimator of cetane number. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Posledná aktualizácia: 2024-09-11 (Počet položiek: 2 346 290)
© Copyright 2024 NORMSERVIS s.r.o.