Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Using Reflectance Spectra to Produce an Index of Temperature Rise in Polymeric Siding
NORMA vydaná dňa 1.4.2021
Označenie normy: ASTM D7990-21
Dátum vydania normy: 1.4.2021
Kód tovaru: NS-1023784
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
heat build, intensity factor, polymeric siding, siding, spectral reflectance, temperature rise,, ICS Number Code 83.140.99 (Other rubber and plastic products),91.060.10 (Walls. Partitions. Facades)
|Significance and Use|
5.1Heat buildup of polymeric building products due to absorption of energy from the sun may lead to distortion problems. Test Method Test Method was developed to predict a building products heat buildup (temperature rise). It compares the relative temperature changes of a pigmented PVC product and a PVC panel containing carbon black when exposed to an infrared heat lamp. Based on experimental results that determined the maximum temperature for this black panel under both solar exposure and in the laboratory test, a method for determining the exterior temperature rise and heat buildup for a test panel was developed. This test has shown to be useful and reliable but is time consuming and requires controlled conditions to minimize sources of variation.
5.2This test method uses a spectrophotometer to measure a specimens reflectance in the ultraviolet, visible, and near infrared region and uses the spectral power distribution of the heat lamp specified in Test Method to determine an intensity factor, which is an index of the relative spectral energy absorption by the specimen.
5.2.1The temperature rise that would occur under an Test Method test is proportional to this intensity factor. An equation has been derived from the correlation of the intensity factor and temperature rise data obtained from Test Method testing of samples with a wide range of color and lightness. A total of 99 samples were studied and represent samples with the lowest to highest temperature rise. Linear regression analysis yields a R2 correlation coefficient of 0.98.
5.2.2The procedure in allows prediction of temperature rise that would result from testing of the same sample under Test Method .
5.2.3As this procedure is a correlation to results obtained by Test Method , it is a method that yields a relative temperature rise compared to black under certain defined severe conditions, but does not predict actual field application temperatures of the product. These product temperatures are influenced by incident angle of the sun, clouds, wind speed, insulation, installation behind glass, etc.
5.3The intensity factor itself is a dimensionless index of the relative energy absorption of the specimen, without conversion to a temperature rise. It can be used to compare the heat buildup characteristics of different colors, or different candidate formulations for the same color. It can also be used to categorize color into ranges of intensity factor, to be used as a basis for testing of full siding products for resistance to thermal distortion.
1.1This test method uses reflectance spectra from the ultraviolet, visible, and near infrared region to produce an index of the temperature rise of polymeric siding above ambient temperature that occurs due to absorption of the suns energy.
1.2The test method determines the intensity factor of a sample color. The intensity factor is a function of the samples reflectance spectra and the energy output of the heat lamp used in the test method Test Method .
1.3 provides a method for using the intensity factor to determine the maximum temperature rise of a sample under severe solar exposure.
1.3.1A correlation between intensity factor and heat buildup (temperature rise) as predicted by Test Method exists.
1.3.2The heat buildup (temperature rise) for a polymeric building product specimen is determined from its reflectance spectra and the correlations regression equation.
1.4UnitsThe values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2022-06-30 (Počet položiek: 2 574 073)
© Copyright 2022 NORMSERVIS s.r.o.