Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D7830/D7830M-13
Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge
Automaticky preložený názov:
Štandardná skúšobná metóda pre In - Place Hustota ( merná hmotnosť ) a obsahu vody v pôde pomocou elektromagnetického pôdy Hustota Gauge
NORMA vydaná dňa 1.2.2013
Informácie o norme:
Označenie normy: ASTM D7830/D7830M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2013
Kód tovaru: NS-39163
Počet strán: 18
Približná hmotnosť: 54 g (0.12 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM D7830/D7830M-13 :
Keywords:
acceptance testing, compaction test, construction control, dry density, electromagnetic density gauge, field density, impedance spectroscopy, in-place density, nondestructive testing, non-nuclear test method, quality control, soil density, wet density, ICS Number Code 13.080.20 (Physical properties of soil)
Doplňujúce informácie
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||
|
5.1 The method described determines wet density and water content by correlating complex impedance measurement data to an empirically developed model. The empirical model is generated by comparing the electrical properties of typical soils encountered in civil construction projects to their wet densities and water contents determined by other accepted methods. 5.2 The test method described is useful as a rapid, non-destructive technique for determining the in-place total density and water content of soil and soil-aggregate mixtures and the determination of dry density. 5.3 This method may be used for quality control and acceptance of compacted soil and soil-aggregate mixtures as used in construction and also for research and development. The non-destructive nature allows for repetitive measurements at a single test location and statistical analysis of the results. 1.1 This test method covers the
procedures for determining in-place properties of non-frozen,
unbound soil and soil aggregate mixtures such as total density,
gravimetric water content and relative compaction by measuring the
electromagnetic impedance of the compacted soil.
1.1.1 The method and device described in this test method are intended for in-process quality control of earthwork projects. Site or material characterization is not an intended result. 1.2 Units—The values stated in either SI units or inch-pound units [given in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.2.1 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight) while the unit for mass is slugs. The rationalized slug unit is not given in this standard. 1.2.2 In the engineering profession, it is customary practice to use, interchangeably, units representing both mass and force, unless dynamic calculations are involved. This implicitly combines two separate systems of units, that is, the absolute system and the gravimetric system. It is undesirable to combine the use of two separate systems within a single standard. The use of balances or scales recording pounds of mass (lbm), or the recording of density in lbm/ft3 should not be regarded as nonconformance with this standard. 1.3 All observed and calculated values shall conform to the Guide for Significant Digits and Rounding established in Practice D6026. 1.3.1 The procedures used to specify how data is collected, recorded, and calculated in this standard are regarded as industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or decrease the number of significant digits of reported data commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in the analysis methods for engineering design. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
|
|
Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
|
|
Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
|
|
Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester
|
|
Standard Test Method for Determination of Water Content of Soil By Direct Heating
|
|
Standard Practice for Using Significant Digits and Data Records in Geotechnical Data
|
|
Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
|
|
Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method (Withdrawn 2024)
|
|
Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
|
|
Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3))
|
|
Standard Test Method for Particle-Size Analysis of Soils
|
|
Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils (Includes all amendments and changes 4/17/2018).
|
|
Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
|
|
Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method (Includes all amendments and changes 4/17/2018).
|
|
Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))
|
|
Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method
|
|
Standard Terminology Relating to Soil, Rock, and Contained Fluids
|
|
Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating
|
|
Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table (Includes all amendments and changes 11/21/2019).
|
|
Standard Test Methods for Determination of Maximum Dry Unit Weight of Granular Soils Using a Vibrating Hammer |
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
