Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Obtaining In-Service Samples of Lubricating Grease
Automaticky preložený názov:
Štandardná prax pre získanie v prevádzke Vzorky mazacieho tuku
NORMA vydaná dňa 1.5.2011
Označenie normy: ASTM D7718-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2011
Kód tovaru: NS-39006
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
rease, grease sampling, grease-sampling device, in-service grease analysis, in-service grease sampling, lubricating grease, Equipment, Grease, Lubricating grease, Sampling, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Significance and Use | ||||||
This practice is typically used to obtain in-service lubricating grease samples from machinery. In this practice, a consistent and repeatable method is outlined for obtaining trendable samples from the following applications including motor-operated valves, gearboxes, pillow-block bearings, electric motors, exposed bearings, open gears, or failed grease-lubricated components. This allows for analysis and inspection of in-service lubricating grease that aids in predicting the life and condition of the grease-lubricated component. This information can be combined with other technologies such as infrared imaging, vibration analysis, and ultrasonic vibration analysis to predict when a machine may fail. The knowledge gained by the aforementioned analyses, in addition to the knowledge gained from the in-service lubricating grease analysis and inspection, may allow for more overall uptime by aiding in the prediction of grease-lubricated component failures as part of a predictive maintenance schedule. The prediction of a failing grease-lubricated component will also improve the level of safety of all who work around the component. |
||||||
1. Scope | ||||||
1.1 This practice covers the method to obtain a trendable in-service lubricating grease sample from the following configurations including motor-operated valves, gearboxes, pillow-block bearings, electric motors, exposed bearings, open gears, or failed grease-lubricated components. 1.2 In some cases, it may be necessary to take more than one sample from a piece of equipment to obtain more trendable results. Examples of this could be a large bearing that does not fully rotate, such as a slew bearing, or one in which sufficient mixing does not otherwise occur. 1.3 Samples taken in the above manner may need to be mixed to form a more homogeneous sample. This may also be true of other samples such as those taken from open face bearings. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. The exception to this is a standard English units thread for which there is no metric equivalent. Note 1—The standard pipe thread referred to is the national pipe thread tapered thread. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historická
1.5.2013
Historická
1.8.2009
Historická
1.5.2014
Historická
15.4.2009
Historická
1.12.2012
Historická
1.10.2010
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.