Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Solvent-Free Membrane Recoverable Oil and Grease by Infrared Determination
Automaticky preložený názov:
Štandardná skúšobná metóda pre neobsahuje rozpúšťadlá membránového obnoviteľného oleje a mazivá infračervenými Stanovenie
NORMA vydaná dňa 1.11.2011
Označenie normy: ASTM D7575-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2011
Kód tovaru: NS-38754
Počet strán: 12
Približná hmotnosť: 36 g (0.08 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
dispersive infrared, filtometric infrared, FTIR, grease, infrared transmission, oil, solid phase extraction, spectroscopy, water: FTIR analysis, Industrial wastewater applications, Infrared (IR) analysis--water, Recoverable elements (from water), Spectroscop, ICS Number Code 13.060.50 (Examination of water for chemical substances)
Significance and Use | ||||||||||||
The presence and concentration of oil and grease in domestic and industrial wastewater is of concern to the public because of its deleterious health, environmental, safety, and aesthetic effects. Regulations and standards have been established that require monitoring of oil and grease in water and wastewater. Note 1—Different oil and grease materials may have different infrared absorptivities. Certain materials, such as synthetic silicone-based or perfluorinated oils, may have absoptivities inconsistent with those of naturally occurring oil and grease materials. Caution should be taken when testing matrices suspected of containing proportions of these materials. In such cases, laboratory spike samples, laboratory check samples, equivalency testing, or combinations thereof, using these materials in question may be appropriate. |
||||||||||||
1. Scope | ||||||||||||
1.1 This test method covers the determination of oil and grease in produced and waste water samples over the concentration range outlined in Table 1 that can be extracted with an infrared-amenable membrane and measured by infrared transmission through the membrane. 1.2 This method defines oil and grease in water as that which is extractable in the test method and measured by infrared transmission. 1.3 The method detection limit (MDL) and recommended reporting range are listed in Table 1. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. TABLE 1 MDL and Reporting Range
A MDL and recommended reporting range determined by Section 12.4, which follows the Code of Federal Regulations, 40 CFR Part 136, Appendix B; limits should be determined by each operator. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Historická
1.8.2010
Historická
15.6.2013
Historická
1.10.2009
Historická
1.10.2009
Historická
15.9.2008
Historická
15.6.2012
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.