ASTM D3837-95(2012)..
ASTM D4142-89(2009)..
ASTM D4217-07(2013)..
ASTM D4242-07(2013)..
ASTM D4301-05(2013)..
ASTM D4426-01(2013)..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D7487-13
Standard Practice for Polyurethane Raw Materials: Polyurethane Foam Cup Test
Automaticky preložený názov:
Štandardné praktiky pre Polyuretánové surovín: Polyuretánová pena Cup test
NORMA vydaná dňa 1.11.2013
Informácie o norme:
Označenie normy: ASTM D7487-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2013
Kód tovaru: NS-38588
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D7487-13 :
Keywords:
cream time, cup test, foam testing, formulated polyol, free rise density, free rise height, free rise time, initiation time, isocyanate, polyurethane, pull time, raw material, resin blend, settle back, sigh back, sink back, string gel time, tack free time, top of cup time, ICS Number Code 83.080.10 (Thermosetting materials)
Doplňujúce informácie
| Significance and Use |
|
5.1 General Utility: 5.1.1 It is useful to verify catalyst levels in a resin blend or a polyurethane system. 5.1.2 This practice is suitable for research, quality control, specification testing, and process control. 5.2 Limitations: 5.2.1 Several of the measured parameters are subjective. Therefore, operator-to-operator variability and lab-to-lab variability can be much higher than that of a single operator. 5.2.2 The variability of this practice is dependent on the consistency of mixing of the reactants. 5.2.3 The estimation of precision in this practice is based on typical formulations for rigid and flexible foams. Formulations with faster reaction times will likely have greater variability, particularly cream time (initiation time). Formulations with slower reaction times will likely have greater variability in the measurement of free rise time. 5.2.4 It is possible that low-level (ppm, ppb) ingredient contamination will not be detectable using this practice. Confirmation of such contamination will potentially require large-scale (~ 20 litres) tests and is out of the scope of this practice. |
| 1. Scope |
|
1.1 This practice covers the determination of cream time (initiation time), top of cup time, free rise time, free rise height, string gel time (pull time), tack free time, settle back, and free rise density of polyurethane foam formulations using a cup foam test. 1.2 Typical definitions, terms, and techniques are described; including procedures for mixing and transferring samples to the foaming container; and data gathering and evaluation. However, agreement between the customer and the testing laboratory for all these items must be obtained prior to use. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
Podobné normy:
Historická
1.10.2012
Historická
1.12.2009
Historická
1.6.2013
Historická
1.6.2013
Historická
1.11.2013
Historická
1.5.2013
Odporúčame:
EviZak - všetky zákony vrátane ich evidencie na jednom mieste
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
