Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Defect Detection and Rating of Plastic Films Using Optical Sensors
NORMA vydaná dňa 1.9.2021
Označenie normy: ASTM D7310-21
Dátum vydania normy: 1.9.2021
Kód tovaru: NS-1036344
Počet strán: 17
Približná hmotnosť: 51 g (0.11 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
blown film, camera, cast film, contamination, defect, digital image analysis, extrusion, film quality, fish eyes, gel, image processor, inspection, lighting, optical sensor, pixel,, ICS Number Code 83.140.10 (Films and sheets)
|Significance and Use|
4.1Defects in film are not acceptable to the end-user as there is a reduction in the fitness-for-use in many applications. This document is intended to be a practice to assist users in the inspection, quantification and observation of defects.
4.2This practice is applicable in a laboratory environment, continuous inspection as a quality control or as a research tool. It is also appropriate for use in any commercial process used to produce film including extrusion, calendaring, etc.
4.3This practice is also suitable for use as an evaluation or screening tool for materials intended to be used in other processes where defects of this nature are critical, such as fiber spinning non-woven, etc.
4.4Results achieved by different equipment, even from the same vendor in the same laboratory, are often not directly comparable as a bias exists that cannot be fully addressed through consistent operating conditions. Results frequently shift when analyzer components are upgraded. Additionally, results are often not directly comparable between different product types. All results are to be considered as relative values rather than absolute.
4.4.1Therefore, it is not recommended to provide absolute results as part of a sales contract between the buyer and seller. For sales contracts, it is recommended to establish product grade designations based on the historical relationship of the absolute results reported, and fitness-for-use or based on a reference material agreed by both parties. This is attained by the collection of data over a time-period to establish acceptable control limits.
4.4.2The defect size range of interest is usually different between resin supplier and converters. Total defect counts are not one to one comparable between small laboratory extrusion lines and commercial extrusion lines. Therefore, an individual correlation is the aim to get accepted results for fitness-for-use.
Note 2:This was tested on Brabender, Collin, Goettfert, and OCS systems.
4.5For support in a basic interpretation of the different results the following points may be helpful for comparison.
4.5.1Size classes (number and definition)
4.5.2Reported defect types
4.5.3Comparable units (gels/kg, gels/m2, class system, index...)
4.5.4Vendor (type of equipment, for example, cast or blown film...)
4.5.5Camera settings (sensitivity, grey level, resolution...)
Note 3:For attribute data such as defect counts, C-type control charts are most appropriate per recommendations within Practice , Section 9.
1.1This practice intends to provide standardized approaches and criteria for the observation and reporting of defects in various types of plastic film, by means of an optical scanning system. Scope includes the in situ inspection of defects in films fabricated for specific applications after preparation of a suitable film from plastic resin.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Posledná aktualizácia: 2023-02-01 (Počet položiek: 2 663 485)
© Copyright 2023 NORMSERVIS s.r.o.