Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Sampling Waste Streams on Conveyors
Automaticky preložený názov:
Štandardná prax pre odber vzoriek z tokov odpadov na dopravníkoch
NORMA vydaná dňa 15.2.2007
Označenie normy: ASTM D7204-07
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.2.2007
Kód tovaru: NS-37856
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
conveyor, incinerator, kiln, lifts, sampling, soil, waste streams, ICS Number Code 13.030.40 (Installations and equipment for waste disposal and treatment)
Significance and Use | ||||||||||||||||||||||||||||||||
This practice can be used in sampling ash from a kiln or incinerator, soils, and process waste from conveying systems, such as, a conveyer and vertical lifts. Some slurries, such as the bottom solids, can be sampled from the quench waters at the end of a kiln. This practice can be used to determine material balances for burner efficiency studies and compliance studies. This practice can be used on lifts, sloping, and horizontal conveyor systems. The type of conveyor and the amount and type of sample required will dictate the type of sampling equipment required to get a representative sample. The sample is taken directly from the conveyor before emptying into the waste container or pile for disposal or recycling using a scoop, dipper, or shovel depending upon the sample requirements (see Practice D 5633). The sample is then put into the sample container for analysis. The place, quantity, frequency, and time of sampling is dependent upon the conveying system equipment, DQOs (Practice D 5792), work or sampling plan (See Practice D 5283 and Guide D 4687), and analysis to be run. 4.5.1 Large particles can be mechanically excluded on a belt system. Large particles may accumulate at the bottom of an inclined/sloped belt system. Therefore, steps, if possible, need to be taken so that particles of all sizes have equal chances of being sampled. 4.5.2 The number of samples and sample time is dependent upon the system, the precision required, the decisions that are to be made, the cost, and the degree of heterogeneity of the material (see Guide D 5956, Practice D 6250, and Guide D 6311). 4.5.3 In general, the ideal sampling location is nearest to the point of generation since temperature, oxidation, and air movement may change some samples with time. The practice does not address issues related to the heterogeneity of the sample. |
||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||
1.1 This practice describes standard procedures for sampling waste on open and closed conveying systems and is applicable to any waste material that can be conveyed to a waste pile or container. The conveyor system can be a vertical (vertical lifts), sloped or horizontal type. 1.2 This practice is intended for particles and slurries, which can be sampled using scoop, dipper or shovel type samplers. 1.3 The practice is not intended for large size sample constituents, such as boulders, large rocks, and debris. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.