Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D705-99

Standard Specification for Urea-Formaldehyde Molding Compounds

Automaticky preložený názov:

Štandardné špecifikácie pre močovinoformaldehydových hmoty na výrobu foriem

NORMA vydaná dňa 10.11.1999

Jazyk
Prevedenie	Online zabezpečené PDF - 66.10 € Tlačené - 66.10 €
Dostupnosť	SKLADOM
Cena	66.10 € bez DPH
66.10 €

Informácie o norme:

Označenie normy: ASTM D705-99
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.11.1999
Kód tovaru: NS-37423
Počet strán: 2
Približná hmotnosť: 6 g (0.01 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM D705-99 :

Keywords:

Formaldehyde, Molding compounds (thermosetting), Urea-formaldehyde, ICS Number Code 83.140.99 (Other rubber and plastic products)

Doplňujúce informácie

1. Scope

1.1 This specification covers compression molding thermosetting compounds consisting of a urea-formaldehyde resin binder intimately combined in the uncured or partially cured condition with fillers, pigments, and other chemical agents.

1.2 The values stated in SI units are to be regarded as the standard. The values stated in parentheses are for information only.

Note 1-The properties included in this specification are those required to identify the types of molding compounds covered. There may be other requirements necessary to identify particular characteristics. Transfer or injection molding will usually result in different physical and electrical characteristics than compression molding.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 2-ISO 2112-1977(E) is similar but not equivalent to this specification. Product classification and characterization are not the same.

2. Referenced Documents

D149-25	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
ISO 2112-1977(E)	Plastics--Aminoplastic Moulding Materials--Specification Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D256-26	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D495-22	Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
D570-22	Standard Test Method for Water Absorption of Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D790-25	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D956-87	Practice for Compression Molding Specimens of Amino Molding Compounds (Withdrawn 1992)
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.