Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D704-99(2004)

Standard Specification for Melamine-Formaldehyde Molding Compounds

Automaticky preložený názov:

Štandardné špecifikácie pre melamínformaldehyd hmoty na výrobu foriem

NORMA vydaná dňa 1.10.2004

Jazyk
Prevedenie	Online zabezpečené PDF - 67.30 € Tlačené - 67.30 €
Dostupnosť	SKLADOM
Cena	67.30 € bez DPH
67.30 €

Informácie o norme:

Označenie normy: ASTM D704-99(2004)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2004
Kód tovaru: NS-37388
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM D704-99(2004) :

Keywords:

formaldehyde, melamine-formaldehyde, molding compounds (thermosetting), ICS Number Code 83.140.99 (Other rubber and plastic products)

Doplňujúce informácie

1. Scope

1.1 This specification covers compression molding, thermosetting, melamine-formaldehyde molding compounds as further defined in , resin binder, with or without other resins, intimately combined with fillers, pigments, and any chemical agents needed.

1.2 The values stated in SI units are to be regarded as the standard. Note 1The properties included in this specification are those required to identify the types of molding compounds covered. There may be other requirements necessary to identify particular characteristics. These will be added to the specification as their inclusion becomes generally desirable and the necessary test data and methods become available. Transfer or injection molding will usually result in different physical and electrical characteristics than compression molding.

Note 2

ISO 2122-1977(E) is similar but not equivalent to this specification. Product classification and characterization are not equivalent.

2. Referenced Documents

D3638-21e1	Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials (Includes all amendments and changes 2/2/2022).
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D495-22	Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
D570-22	Standard Test Method for Water Absorption of Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D648-18	Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
D731-22	Standard Test Method for Molding Index of Thermosetting Molding Powder
D790-25	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883-26a	Standard Terminology Relating to Plastics (Includes all amendments and changes 6/15/2026).
D1895-24	Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials
D1896-09	Standard Practice for Transfer Molding Test Specimens of Thermosetting Compounds
D149-25	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D150-22	Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D256-26	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D3795-20	Standard Test Method for Thermal Flow, Cure, and Behavior Properties of Pourable Thermosetting Materials by Torque Rheometer
Manual 7	Manual on Presentation of Data and Control Chart Analysis, 8th Edition Available from ASTM International Headquarters. Request MNL7-8TH.
D5224-12(2019)	Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds
D6289-13(2019)	Standard Test Method for Measuring Shrinkage from Mold Dimensions of Molded Thermosetting Plastics
ISO 2122-1977(E)	Plastics--Aminoplastic Molding Materials--Specification Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.