Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D6794-20e1
Standard Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6 h) Heating Time (Includes all amendments and changes 6/22/2022).
NORMA vydaná dňa 1.5.2020
Informácie o norme:
Označenie normy: ASTM D6794-20e1
Dátum vydania normy: 1.5.2020
Kód tovaru: NS-1065683
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D6794-20e1 :
Keywords:
engine lubricating oil, filterability, storage,, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Doplňujúce informácie
| Significance and Use | ||||||||||
|
5.1 It is normal for some of the combustion products of an internal combustion engine to penetrate into the engine lubricant and be retained in it. 5.2 When an engine is run for a period of time and then stored over a long period of time, the by-products of combustion might be retained in the oil in a liquefied state. 5.3 Under these circumstances, precipitates can form that impair the filterability of the oil the next time the engine is run. 5.4 This test method subjects the test oil and the new oil to the same treatments such that the loss of filterability can be determined. The four water treatment levels may be tested individually, all four simultaneously, or any combination of multiple water treatment levels. 5.5 Reference oils, on which the data obtained by this test method is known, are available. 5.6 This test method requires that a reference oil also be tested and results reported. Two oils are available, one known to give a low and one known to give a high data value for this test method. Note 1: When the new oil test results are to be offered as
candidate oil test results for a specification, such as
Specification D4485, the
specification will state maximum allowable loss of filterability
(flow reduction) of the test oil as compared to the new
oil.
|
||||||||||
| 1. Scope | ||||||||||
|
1.1 This test method covers the determination of the tendency of an oil to form a precipitate that can plug an oil filter. It simulates a problem that may be encountered in a new engine run for a short period of time, followed by a long period of storage with some water in the oil. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
| 2. Referenced Documents | ||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
