Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determination of Isothermal Secant and Tangent Bulk Modulus (Withdrawn 2021)
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie Izotermní sečná a dotýkajúci objemový modul
NORMA vydaná dňa 15.4.2012
Označenie normy: ASTM D6793-02(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.4.2012
Kód tovaru: NS-36559
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
density, dynamic bulk modulus, isentropic bulk modulus, isothermal bulk modulus, isothermal secant bulk modulus, isothermal tangent bulk modulus, pressure, static bulk modulus, Compressibility, Dynamic analysis/testing, Isentropic bulk modulus, Isothermal conditions/testing, Secant bulk modulus, Static bulk modulus, Tangent bulk modulus, ICS Number Code 75.160.20 (Liquid fuels)
Significance and Use | ||||||||
Isothermal secant bulk modulus (static bulk modulus) is a property that measures the compressibility of a liquid. The greater the value, the less the compressibility of the liquid. Isothermal secant bulk modulus is employed in the design of high performance hydraulic fluid and braking systems. High bulk modulus is desirable in that the response time of a system is faster when applied pressure more directly effects the action of the system rather than in the compression of the working liquid. If isothermal secant bulk modulus is known as a function of pressure, the data may be used to calculate isothermal tangent bulk modulus and density as a function of pressure. The data may not, however, be used to determine isentropic (dynamic) bulk modulus. That property is usually determined from velocity of sound measurements and differs from isothermal bulk modulus by the ratio of Cp/Cv = γ (the ratio of heat capacity at constant pressure to that at constant volume for the test specimen. |
||||||||
1. Scope | ||||||||
1.1 This test method covers the determination of isothermal secant and tangent bulk modulus of liquids which are stable and compatible with stainless steel under the conditions of test. 1.2 This test method is designed to be used over the temperature range from -40 to 200°C and from ambient to 68.95 Mpa (10 000 psig). Note 1—Because of the design of the test apparatus, the upper limit of pressure which can be attained is limited by the bulk modulus of the test fluid. Pressures as high as 68.95 Mpa will not be attained for fluids of relatively low bulk modulus at the test temperature. 1.3 This test method assumes that the user is proficient in the assembly and use of medium pressure (m/p) threaded and coned fittings which are intended for use at pressures up to 137.9 Mpa (20 000 psig). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—Because hydraulic pressure in the test system is produced by purely mechanical means, the test method is not subject to the hazards associated with systems which are pressurized pneumatically. Even small leaks will result in immediate drop in pressure to ambient without production of a high pressure liquid stream or mist. |
||||||||
2. Referenced Documents | ||||||||
|
Historická
1.5.2014
Historická
1.12.2013
Historická
1.5.2013
Historická
1.12.2012
Historická
1.9.2010
Historická
1.6.2014
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.