Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determination of Ply Adhesion Strength of Reinforced Geomembranes
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie Ply priľnavosť povlaku z vystuženého Geomembranes
NORMA vydaná dňa 1.6.2011
Označenie normy: ASTM D6636-01(2011)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2011
Kód tovaru: NS-35964
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
geomembrane, ply adhesion, reinforced, Geosynthetics, Reinforced geomembranes, Adhesion, Ply adhesion strength, ICS Number Code 91.100.50 (Binders. Sealing materials)
Significance and Use | ||||||||
This method is an index test and measures the force required to separate individual plies of a reinforced geomembrane. The acceptable value of adhesion will vary for different types of products. However for a particular type of product, minimum values of ply adhesion can be determined and agreed to by producer and consumer, and both can monitor to assure compliance with the agreed-upon value. Disputes—In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical difference between their laboratories. Competent statistical assistance is recommended for the investigation of this difference. As a minimum, the two parties should take a group of test specimens which are from the same lot of material as those type in question and which are as homogeneous as possible. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing began. If a difference is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in the light of the known difference. |
||||||||
1. Scope | ||||||||
1.1 This test method covers the measurement of the adhesion strength (180° peel) between plies of reinforced geomembranes such as internally reinforced geomembranes and coated fabrics. 1.2 This test method is not intended for determining the strength of geomembrane seams or for determining the ply adhesion strength of geocomposite components (such as nonwoven geotextile bonded to geomembrane, or geotextile bonded to drainage core). 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||
2. Referenced Documents | ||||||||
|
Historická
1.6.2012
Historická
1.7.2007
Historická
1.6.2014
Historická
15.8.2011
Historická
1.7.2011
Historická
1.6.2010
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.