Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Guide for Application of Fully Adhered Hot-Applied Reinforced Waterproofing Systems
Automaticky preložený názov:
Štandardné Pokyny pre použitie plne dodržiavané Hot-Aplikovaná Reinforced hydroizolačných systémov
NORMA vydaná dňa 1.1.2009
Označenie normy: ASTM D6622-01(2009)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2009
Kód tovaru: NS-35927
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
application, asphalt, coal tar pitch, modified bitumen, polymer-modified bitumen sheet, rubberized asphalt waterproofing, waterproofing, Application--roofing/waterproofing material, Fully-adhered waterproofing systems, Reinforced roofing/waterproofing materials, Waterproofing materials/applications, ICS Number Code 91.100.50 (Binders. Sealing materials)
Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
This guide outlines general procedures and precautions for the application of fully adhered hot-applied built-up reinforced waterproofing systems. This guide is not all inclusive and is intended only to supplement detailed instructions from designers, and the recommendations of manufacturers. Manufacturers of some of the systems addressed by this guide require proprietary products and special procedures not described in this guide. Manufacturers' recommendations should therefore be considered in the application of this guide. For design guidelines, consult Guide C 981. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces. 1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Historická
1.6.2010
Historická
1.4.2014
Historická
1.6.2012
Historická
1.7.2007
Historická
1.6.2014
Historická
15.8.2011
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.