Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
NORMA vydaná dňa 1.4.2018
Označenie normy: ASTM D648-18
Dátum vydania normy: 1.4.2018
Kód tovaru: NS-845274
Počet strán: 14
Približná hmotnosť: 42 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
deflection temperature, flexural load, flexure,, ICS Number Code 83.080.01 (Plastics in general)
Significance and Use | ||||||||||||||||||||||||||
5.1 This test is particularly suited to control and development work. Data obtained by this test method shall not be used to predict the behavior of plastic materials at elevated temperatures except in applications in which the factors of time, temperature, method of loading, and fiber stress are similar to those specified in this test method. The data are not intended for use in design or predicting endurance at elevated temperatures. 5.2 For many materials, there may be a specification that requires the use of this test method, but with some procedural modifications that take precedence when adhering to the specification. Therefore, it is advisable to refer to that material specification before using this test method. Refer to Table 1 in Classification D4000, which lists the ASTM material standards that currently exist. |
||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||
1.1 This test method covers the determination of the temperature at which an arbitrary deformation occurs when specimens are subjected to an arbitrary set of testing conditions. 1.2 This test method applies to molded and sheet materials available in thicknesses of 3 mm (1/8 in.) or greater and which are rigid or semirigid at normal temperature. Note 1: Sheet stock less than 3 mm (0.125 in.) but more than 1
mm (0.040 in.) in thickness may be tested by use of a composite
sample having a minimum thickness of 3 mm. The laminae must be of
uniform stress distribution. One type of composite specimen has
been prepared by cementing the ends of the laminae together and
then smoothing the edges with sandpaper. The direction of loading
shall be perpendicular to the edges of the individual
laminae.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 Some older machines still use mercury-in-glass thermometers. (Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2: The text of this standard references notes and
footnotes that provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be
considered as requirements of the standard.
Note 3: This standard and ISO 75-1 and ISO 75-2 address the
same subject matter, but differ in technical content, and results
shall not be compared between the two test methods.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||
|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.