Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie konkrétnych zbaliteľnosti a tkanín používaných v airbagy
NORMA vydaná dňa 1.7.2014
Označenie normy: ASTM D6478-10(2014)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2014
Kód tovaru: NS-35303
Počet strán: 9
Približná hmotnosť: 27 g (0.06 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Karosérie a součásti karosérie silničních vozidel
Textilní tkaniny
Keywords:
airbag, fabric, inflatable restraint, packability, packing, volume, ICS Number Code 43.040.60 (Bodies and body components), 59.080.30 (Textile fabrics)
Significance and Use | ||||||||||||||
5.1 This test method is useful for determining the specific packability of uncoated and coated airbag fabrics. Fabric packability is an important factor in the design of airbag modules due to their inherent spacial constraints. 5.2 A folded specimen exhibits better specific packability if it occupies a lower total volume at the specified loads compared to another specimen. 5.3 The time required to test one sample (four specimens from the same lot of fabric) is approximately 1.5 h using this test method. Due to the length of time required by this test method to perform a single test, this test method is most suitable for use in design and development analysis or for inclusion in a list of required tests conducted for annual certification of an airbag fabric. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This test method covers procedures for determining the ability to fold and pack fabrics used for inflatable restraints using an index of specific packability. 1.2 Procedures in this test method describe operator techniques that must be followed closely to obtain repeatable and accurate results. Since these techniques are difficult to convey in writing, supplemental training for operators is required. A training video is available from ASTM (see Adjuncts ADJD6478 and ADJD6478A). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Procedures and apparatus other than those stated in this practice may be used as agreed upon between the purchaser and the supplier with specific deviations from this practice acknowledged in the report. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Historická
1.2.2011
Historická
1.7.2013
Historická
1.6.2011
Historická
1.7.2012
Historická
1.7.2012
Historická
1.11.2011
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.