Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Methods for Loop Tack
NORMA vydaná dňa 1.10.2022
Označenie normy: ASTM D6195-22
Dátum vydania normy: 1.10.2022
Kód tovaru: NS-1088641
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
adhesive, loop tack, pressure-sensitive article, tack,, ICS Number Code 83.180 (Adhesives)
Significance and Use | ||||||||||||||||||
5.1?These test methods provide a quantitative measure of the pressure-sensitive tack property of an adhesive. FIG. 1?Loop Tack Test Fixture 1 FIG. 2?Loop Tack Test Fixture 2 FIG. 3?Loop Tack Sample During Test 5.2?These test methods are designed to measure the tack property of the adhesive mass. The tack of a given adhesive varies depending on the backing (generally, stiffer backings lead to higher values). 5.3?Theses test methods are suitable for quality control and research purposes. 5.4?Test Method A?(using Tensile Tester) makes use of a specimen strip 7 in. (175 mm) in length. Both the FINAT FTM 9 Quick Stick Tack Measurement Test and the TLMI L-IB2 Tensile Tester Loop Tack Test also use a specimen strip of that length. 5.5?Test Method B?(using Loop Tack Tester) makes use of a specimen strip five in. (125 mm) in length. That is the only length specimen strip that fits properly in the loop tack tester. 5.6?If the adhesive is not already otherwise coated, these test methods incorporate the use of a clear 2 mil (0.05 mm) polyester (PET) film backing for specimen preparation. Use of other backing materials changes performance of the specimen to be tested. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1?These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface. Tack force may be measured as the force required to separate the adhesive from the adherend at the interface shortly after they have been brought into contact under a load equal only to the weight of the pressure-sensitive article (for example, tape, label, sticker, etc.) on a 1 in.2 contact area. 1.2?The following test methods are included: 1.2.1?Test Method A?(using Tensile Tester), and 1.2.2?Test Method B?(using Loop Tack Tester). 1.3?The values stated in inch-pound units are to be regarded as the standard because the industry standard width for pressure-sensitive tape is 1 inch. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-29 (Počet položiek: 2 209 895)
© Copyright 2024 NORMSERVIS s.r.o.