Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Glow-Wire Ignition of Materials
Automaticky preložený názov:
Štandardná skúšobná metóda pre Glow - Wire zapaľovanie materiálov
NORMA vydaná dňa 1.3.2010
Označenie normy: ASTM D6194-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2010
Kód tovaru: NS-34173
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
ISO 13943 Fire Safety´Vocabulary , Electrical insulating plastics, Electrically heated sources, Glow-wire ignition, Ignition--electrical insulating materials, ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products), 29.035.01 (Insulating materials in general)
Significance and Use | ||||||||||||||||
During operation of electrical equipment, including wires, resistors, and other conductors, it is possible for overheating to occur under certain conditions of operation, or when malfunctions occur. When this happens, a possible result is ignition of the adjacent insulation material. This test method assesses the susceptibility of electrical insulating materials to ignition as a result of exposure to a glowing wire. This test method determines the minimum temperature required to ignite a material by the effect of a glowing heat source, under the specified conditions of test. This method is suitable, subject to the appropriate limitations of an expected precision of ±15 %, to categorize materials. 5.5 In this procedure, the specimens are subjected to one or more specific sets of laboratory conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method covers the minimum temperature required to ignite insulating materials using a glowing heat source. In a preliminary fashion, this test method differentiates between the susceptibilities of different materials with respect to their resistance to ignition due to an electrically-heated source. 1.2 This test method applies to molded or sheet materials available in thicknesses ranging from 0.25 to 6.4 mm. 1.3 This test method is not valid for determining the ignition behavior of complete electrotechnical equipment, since the design of the electrotechnical product influences the heat transfer between adjacent parts. 1.4 This test method measures and describes the response or materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See for further details.) 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9. 1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. Note 1—Although this test method and IEC 60695-2-13 differ in approach and in detail, data obtained using either are technically equivalent. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.