Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
Automaticky preložený názov:
Štandard Specification pre lisované, lisované a vstrekovaných polyoxymethylenová tvary (POM)
NORMA vydaná dňa 1.5.2014
Označenie normy: ASTM D6100-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2014
Kód tovaru: NS-33780
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
POM, centerline porosity&mdash,POM, copolymer&mdash,POM, homopolymer&mdash,POM, low porosity&mdash,POM, plates&mdash,POM, porosity level 1&mdash,POM, recycled&mdash,POM, rod&mdash,POM, shapes&mdash,POM, sheet&mdash,POM, tubular bar&mdash,POM, ICS Number Code 71.080.10 (Aliphatic hydrocarbons)
1. Scope | ||||||||||||||||
1.1 This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded, compression molded and injection molded polyoxymethylene (POM) sheet, plate, rod, and tubular bar shapes, excluding pipe and fittings. 1.2 The properties included in this specification are those required for the compositions covered. Section 1.3 This specification allows for the use of recycled plastics. 1.4 The values stated in inch-pound units are to be regarded as the standard in all property and dimensional tables. For reference purposes, SI units are included in Table S-POM and Table 1 only. 1.5 The following precautionary caveat pertains only to the test method portions, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
|
|
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
|
|
Standard Terminology Relating to Plastics
|
|
Standard Practice for Conditioning Plastics for Testing
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Practice for Packaging/Packing of Plastics
|
|
Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)
|
|
Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
Historická
1.12.2008
Historická
1.11.2012
Historická
1.2.2013
Historická
1.11.2012
Historická
15.6.2013
Historická
1.6.2013
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.