Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone Corrosimeter
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie poleptanie spalín pomocou Cone Corrosimeter
NORMA vydaná dňa 1.4.2011
Označenie normy: ASTM D5485-11
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2011
Kód tovaru: NS-31405
Počet strán: 14
Približná hmotnosť: 42 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
cone calorimeter, cone corrosimeter, conical heater, corrosion damage, corrosive potency, corrosivity, electrical insulations or coverings, fire, fire test response, ignition, radiant heat, smoke corrosivity, Cone corrosimeter, Corrosimeter, Combustion, Corrosion damage, Corrosive potency, Corrosivity, Electrical insulating materials, Electrical insulating solids, Electrical insulations/coverings, Fire testing--electrical insulating materials, Fire-test response, Gas sampling
Significance and Use | ||||||||||||||||
The metal loss from corrosion is directly related to the increase in electrical resistance of the target due to the decrease in conductive cross-sectional area. The relationship between resistance increase of metallic targets used in this test method and the amount of metal loss as reported by a uniform loss in thickness has not been determined. This test method is used to determine the corrosive effect of combustion products from burning electrical insulations or coverings or their constituent materials or components. Corrosion is determined by the reduction of thickness of the metal on standardized targets, as measured by electrical resistance. These targets are not necessarily representative of the intended end use. This test method is intended for use in electrical insulations or coverings material and product evaluations, for additional data to assist in design of electrical insulations or coverings products, or for development and research of electrical insulations or coverings products. A value of the heating flux is selected to be relevant to the fire scenario being investigated (up to 100 kW/m2). Additional information for testing is given in A1.2.3. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products. 1.2 This test method provides corrosion results of product and material specimens limited to a maximum size of 100 by 100 mm in area and 50 mm thick. 1.3 The results of this test method have not been investigated with respect to correlation to actual fires. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See ) 1.5 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.5.1 Additional information regarding the targets, the test conditions, and test limitations are provided in the annex. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Historická
1.2.2009
Historická
15.8.2011
Historická
1.4.2013
Historická
1.4.2008
Historická
1.3.2011
Historická
1.4.2012
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-04-28 (Počet položiek: 2 896 137)
© Copyright 2024 NORMSERVIS s.r.o.