Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D5373-21
Standard Test Methods for Determination of Carbon, Hydrogen and Nitrogen in Analysis Samples of Coal and Carbon in Analysis Samples of Coal and Coke
NORMA vydaná dňa 1.4.2021
Informácie o norme:
Označenie normy: ASTM D5373-21
Dátum vydania normy: 1.4.2021
Kód tovaru: NS-1022875
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D5373-21 :
Keywords:
analysis sample, carbon, carbon dioxide, coal, coke, hydrogen, moisture, nitrogen,, ICS Number Code 75.160.10 (Solid fuels)
Doplňujúce informácie
| Significance and Use | ||||||||||||||||||
|
5.1?Carbon and hydrogen values can be used to determine the amount of oxygen (air) required in combustion processes and for calculation of the efficiency of combustion processes. 5.2?Carbon and hydrogen determinations can be used in calculations including material balance, reactivity and yields of products relevant to coal conversion processes such as gasification and liquefaction. 5.3?Carbon and nitrogen values can be used in material balance calculations employed for emission accounting purposes. Note 2:?The bulk composition of coal changes at a rate that
varies from coal to coal during storage. As a result, using coal
for calibration can yield incorrect estimates of carbon, and
hydrogen content in particular.
|
||||||||||||||||||
| 1. Scope | ||||||||||||||||||
|
1.1?Test Method A covers the determination of carbon in the range of 54.9 % to 84.7 %, hydrogen in the range of 3.26 % to 5.08 %, and nitrogen in the range of 0.57 % to 1.76 % in analysis samples (8.1) of coal and of carbon in analysis samples of coke in the range of 86.6 % to 97.9 %. 1.1.1?Test Method B covers the determination of carbon in analysis samples of coal in the range of 57.7 % to 84.0 %, and carbon in analysis samples of coke in the range of 86.3 % to 95.4 %. Note 1:?The coals included in the interlaboratory studies
employed to derive the precision statements for this standard cover
ASTM rank lignite A to low volatile bituminous. Additional
information concerning the composition of these coals appears in
Annex A4 and Annex A5. The cokes used in the
interlaboratory study employed to derive the precision statement
for coke for Method A included five each metallurgical (met) cokes
and seven each petroleum (pet) cokes, and Method B included an
equal number (five each) of met cokes and pet cokes.
1.2?All percentages are percent mass fractions unless otherwise noted. 1.3?UnitsThe values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||
|
Doporučujeme:
