Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D5334-14

Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure

Automaticky preložený názov:

Štandardná skúšobná metóda pre stanovenie tepelnej vodivosti pôdy a Soft Rock od Thermal Ihla Probe poriadku

NORMA vydaná dňa 1.6.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 79.90 € Tlačené - 79.90 €
Dostupnosť	SKLADOM
Cena	79.90 € bez DPH
79.90 €

Informácie o norme:

Označenie normy: ASTM D5334-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2014
Kód tovaru: NS-30773
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Fyzikální vlastnosti půd

Anotácia textu normy ASTM D5334-14 :

Keywords:

heat flow, needle probe, temperature, thermal conductivity, thermal probe, thermal properties, ICS Number Code 13.080.20 (Physical properties of soil)

Doplňujúce informácie

Significance and Use

5.1 The thermal conductivity of both intact and reconstituted soil specimens as well as soft rock specimens is used to analyze and design systems used, for example, in underground transmission lines, oil and gas pipelines, radioactive waste disposal, geothermal applications, and solar thermal storage facilities.

Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing. Users of this standard are cautioned that compliance with Practice D3740 does not in itself ensure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.

1. Scope

1.1 This test method presents a procedure for determining the thermal conductivity (λ) of soil and soft rock using a transient heat method. This test method is applicable for both intact and reconstituted soil specimens and soft rock specimens. This test method is suitable only for homogeneous materials.

1.2 This test method is applicable to dry or unsaturated materials over temperatures ranging from <0 to >100°C, depending on the suitability of the thermal needle probe construction to temperature extremes. However, care must be taken to prevent significant error from: (1) redistribution of water due to thermal gradients resulting from heating of the needle probe; 1.3 Units—The values stated in SI units are to be regarded as the standard. No other units of measurements are included in this standard.

1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.4.1 The procedure used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D3740-23	Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
D653-22	Standard Terminology Relating to Soil, Rock, and Contained Fluids
D2216-19	Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
D4439-24	Standard Terminology for Geosynthetics
D6026-21	Standard Practice for Using Significant Digits and Data Records in Geotechnical Data
D4753-24	Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing