Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D5299/D5299M-18
Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
NORMA vydaná dňa 15.11.2018
Informácie o norme:
Označenie normy: ASTM D5299/D5299M-18
Dátum vydania normy: 15.11.2018
Kód tovaru: NS-906346
Počet strán: 18
Približná hmotnosť: 54 g (0.12 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D5299/D5299M-18 :
Keywords:
aquifer, borehole drilling, borehole plugging, decommissioning, groundwater monitoring wells, hazardous waste, overdrilling, well closure, well plugging, well sealing,, ICS Number Code 93.025 (External water conveyance systems)
Doplňujúce informácie
| Significance and Use |
|
5.1 Decommissioning of boreholes and monitoring wells, and other devices requires that the specific characteristics of each site be considered. The wide variety of geological, biological, and physical conditions, construction practices, and chemical composition of the surrounding soil, rock, waste, and groundwater precludes the use of a single decommissioning practice. The procedures discussed in this guide are intended to aid the geologist or engineer in selecting the tasks needed to plan, choose materials for, and carry out an effective permanent decommissioning operation. Each individual situation should be evaluated separately and the appropriate technology applied to meet site conditions. Considerations for selection of appropriate procedures are presented in this guide, but other considerations based on site specific conditions should also be considered. Note 6: Ideally, decommissioning should be considered as an
integral part of the design of the monitoring well. Planning at
this early stage can make the decommissioning activity easier to
accomplish. See Practice D5092 for details on monitoring well
construction.
5.2 This guide is intended to provide technical information and is not intended to supplant statutes or regulations of local governing bodies. Approval of the appropriate regulatory authorities should be an important consideration during the decommissioning process. This practice is in general accordance with other national and state guidance documents on well decommissioning (ANSI/NGWA-01-14 [1]1 and California EPA [2]. Note 7: The quality of the result produced by this standard is
dependent on the competence of the personnel performing it, and the
suitability of the equipment and facilities used. Agencies that
meet the criteria of D3740
are generally considered capable of competent and objective
testing/sampling/inspection/etc. Users of this standard are
cautioned that compliance with Practice D3740 does not in itself assure reliable
results. Reliable results depend on many factors, Practice
D3740 provides a means of
evaluating some of those factors. Practice D3740 was developed for agencies engaged
in laboratory testing and/or inspection of soils and rock. As such,
it is not totally applicable to agencies performing this practice.
However, users of this practice should recognize that the framework
of Practice D3740 is
appropriate for evaluating the quality of an agency performing this
practice. Currently, there is no known qualifying national
authority that inspects agencies that perform this
practice.
Note 8: An extensive research program on annular sealants was
conducted from 2001 through 2009 and in subsequent years by the
Nebraska Grout Task Force Note 9: The decommissioning of wells that intersect openings,
fractured layers or other large openings, such as caves, can make
sealing and decommissioning efforts difficult. The decommissioning
of wells in areas known to have these conditions should involve
professionals experienced in decommissioning in these
areas.
|
| 1. Scope |
|
1.1 This guide covers procedures that are specifically related to permanent decommissioning (closure) of the following as applied to environmental activities. It is intended for use where solid or hazardous materials or wastes are found, or where conditions occur requiring the need for decommissioning. The following devices are considered in this guide: 1.1.1 A borehole used for geoenvironmental purposes (see Note 1), 1.1.2 Monitoring wells, 1.1.3 Observation wells, 1.1.4 Injection wells (see Note 2), 1.1.5 Piezometers, 1.1.6 Wells used for the extraction of contaminated groundwater, the removal of floating or submerged materials other than water such as gasoline or tetrachloroethylene, or other devices used for the extraction of soil gas, 1.1.7 A borehole used to construct a monitoring well, and 1.1.8 Any other well or boring that houses a vadose zone monitoring device. 1.2 Temporary decommissioning of the above is not covered in this guide. Note 1: This guide may be used to decommission boreholes where
no contamination is observed at a site (see Practice D420 for details); however, the primary
use of the guide is to decommission boreholes and wells where solid
or hazardous waste have been identified. Methods identified in this
guide can also be used in other situations such as the
decommissioning of water supply wells and boreholes where water
contaminated with nonhazardous pollutants (such as nitrates or
sulfates) are present. This guide should be consulted in the event
that routine geotechnical studies indicate the presence of
contamination at a site. Consult and follow national, state, or
local regulations as they may control required decommissioning
procedures.
Note 2: The term “well” is used in this guide to denote
monitoring wells, piezometers, or other devices constructed in a
manner similar to a well. Some of the devices listed such as
injection and extraction wells can be decommissioned using this
guide for information but are not specifically covered in detail in
the text.
Note 3: Details on the decommissioning of multiple-screened
wells are not provided in this guide due to the many methods used
to construct these types of wells and the numerous types of
commercially available multiple-screened well systems. However, in
some instances, the methods presented in this guide may be used
with few changes. An example of how this guide may be used is the
complete removal of the multiple-screened wells by
overdrilling.
1.3 Most monitoring wells and piezometers are intended primarily for water quality sampling, water level observation, or soil gas sampling, or combination thereof, to determine quality. Many wells are relatively small in diameter typically 2.5 to 20 cm [1 to 8 inches] and are used to monitor for hazardous chemicals in groundwater. Decommissioning of monitoring wells is necessary to: 1.3.1 Eliminate the possibility that the well is used for purposes other than intended, 1.3.2 Prevent migration of contaminants into an aquifer or between aquifers, 1.3.3 Prevent migration of contaminants in the vadose zone, 1.3.4 Reduce the potential for vertical or horizontal migration of fluids in the well or adjacent to the well, and 1.3.5 Remove the well from active use when the well is no longer capable of rehabilitation or has failed structurally; is no longer needed for monitoring; is no longer capable of providing representative samples or is providing unreliable samples; is required to be decommissioned; or to meet regulatory requirements. Note 4: The determination of whether a well is providing a
representative water quality sample is not defined in this guide.
Examples of when a representative water quality sample may not be
collected include the biological or chemical clogging of well
screens, a drop in the water level to below the base of the well
screen, or complete silting of the screen. These conditions may
indicate that a well is not functioning correctly.
1.4 This guide is intended to provide information for effective permanent closure of wells so that the physical structure of the well does not provide a means of hydraulic communication between aquifers, with above surfaces or react chemically in a detrimental way with the environment. 1.5 The intent of this guide is to provide procedures that when followed result in a reasonable level of confidence in the integrity of the decommissioning activity. However, it may not be practical to verify the integrity of the decommissioning procedure. Currently, methods are not available to substantially determine the integrity of the decommissioning activity. 1.6 This guide may also be used for closure or decommissioning of other systems that could allow vertical or horizontal migration of contaminants or other cross-contamination of aquifers, such as dug wells, geothermal loops, or when ordered by regulatory agencies. 1.7 Units—The values stated in either SI units or inch-pound units (given in brackets) are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word“ Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. Note 5: If state and local regulations are in effect where the
decommissioning is to occur, the regulations take precedence over
this guide.
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
