ASTM E2126-11
ASTM E2127-01a(2007)..
ASTM E2128-12
ASTM E2270-13
ASTM E2273-03(2011)..
ASTM E2511-09
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D5206-13
Standard Test Method for Windload Resistance of Rigid Plastic Siding
Automaticky preložený názov:
Štandardná skúšobná metóda pre Windload Odolnosť tuhého plastu Siding
NORMA vydaná dňa 1.1.2013
Informácie o norme:
Označenie normy: ASTM D5206-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2013
Kód tovaru: NS-30276
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D5206-13 :
Keywords:
PVC siding, plastic siding, siding failure modes, test methods, windload resistance, ICS Number Code 91.060.10 (Walls. Partitions. Facades)
Doplňujúce informácie
| Significance and Use | ||||||||||
|
5.1 This test method is a standard procedure for determining windload resistance of rigid plastic siding under specified uniform static pressure difference. This typically is intended to represent the effects of wind loads on exterior building surfaces. The actual loading on building surfaces is quite complex, varying with wind direction, time, height above ground, building shape, terrain, surrounding structures, and other factors. 5.2 Design wind pressure is selected for specific geographical locations from wind velocity maps prepared by the National Weather Service or other sources. Refer to Annex A1 of Specification D3679 for additional detailed information relating to use of this test method for evaluation of rigid poly(vinyl chloride) (PVC) siding. 1.1 This test method describes
methods for testing and evaluating windload resistance of rigid
plastic siding when fastened in accordance with Practice D4756.
1.2 The proper use of this test method requires a knowledge of the principles of pressure measurement. 1.3 This test method describes the apparatus and the procedures to be used to determine an average maximum sustained static test pressure, or ultimate test pressure values, or both, with static pressure applied uniformly to a specimen. 1.4 The values expressed in
inch-pound units are to be regarded as the standard. The SI
equivalents in parentheses are for information only.
1.5 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Terminology Relating to
Plastics Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) Standard Specification for Rigid
Poly(Vinyl Chloride) (PVC) Siding Standard Practice for Installation of
Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit Standard Terminology of Building
Constructions |
Podobné normy:
Historická
1.5.2011
Historická
1.4.2007
Historická
1.1.2012
Historická
1.11.2013
Historická
1.4.2011
Historická
1.4.2009
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
