Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D519-04(2013)
Standard Test Method for Length of Fiber in Wool Top (Withdrawn 2022)
Automaticky preložený názov:
Štandardná skúšobná metóda pre dĺžky vlákna vo vate Hore
NORMA vydaná dňa 1.7.2013
Informácie o norme:
Označenie normy: ASTM D519-04(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2013
Kód tovaru: NS-30190
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D519-04(2013) :
Keywords:
fiber length, top, wool, ICS Number Code 59.060.10 (Natural fibres)
Doplňujúce informácie
| Significance and Use | |||||||||||||||||||
|
5.1 Knowledge of the average fiber length and the distribution of fibers is of primary importance to users of top in further processing. 5.2 Acceptance specifications for the fiber length and length distribution may be established by the user based on the type of yarn-making equipment employed and the desired end uses. 5.3 Test Method D519 for testing wool top for fiber length is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade for acceptance testing and the current estimates of the between-laboratory precisions are acceptable. 5.3.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative testing to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogenous as possible and that are from a lot of the type material in question. The test specimens should then be assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found either its cause must be found and corrected or the purchaser and supplier must agree to interpret future test results in the light of the known bias.
FIG. 1 Wool Fiber Stapling
Apparatus
Class Intervals, in.
|
Mass, g |
Percentages |
Cumulative Frequencies |
||||||||||||||||
|
First Cumulative, |
Second Cumulative, |
||||||||||||||||||
|
6.0 to 6.5 |
0.014 |
2.4 |
100.0 |
840.1 |
|||||||||||||||
|
5.5 to 6.0 |
0.010 |
1.7 |
97.6 |
740.1 |
|||||||||||||||
|
5.0 to 5.5 |
0.013 |
2.2 |
95.9 |
642.5 |
|||||||||||||||
|
4.5 to 5.0 |
0.018 |
3.1 |
93.7 |
546.6 |
|||||||||||||||
|
4.0 to 4.5 |
0.038 |
6.5 |
90.6 |
452.9 |
|||||||||||||||
|
3.5 to 4.0 |
0.051 |
8.7 |
84.1 |
362.3 |
|||||||||||||||
|
3.0 to 3.5 |
0.062 |
10.6 |
75.4 |
278.2 |
|||||||||||||||
|
2.5 to 3.0 |
0.072 |
12.3 |
64.8 |
202.8 |
|||||||||||||||
|
2.0 to 2.5 |
0.079 |
13.5 |
52.5 |
138.0 |
|||||||||||||||
|
1.5 to 2.0 |
0.080 |
13.6 |
39.0 |
85.5 |
|||||||||||||||
|
1.0 to 1.5 |
0.065 |
11.0 |
25.4 |
46.5 |
|||||||||||||||
|
0.5 to 1.0 |
0.045 |
7.7 |
14.4 |
21.1 |
|||||||||||||||
|
0 to 0.5 |
0.039 |
6.7 |
6.7 |
6.7 |
|||||||||||||||
|
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|||||||||||||||
|
Totals |
0.586 |
100.0 = ∑ |
840.1 |
4363.3 |
|||||||||||||||
|
|
Divided by ∑percentages |
F 1 = 8.40 |
F 2 = 43.63 |
||||||||||||||||
B = the largest midpoint value for which a
frequency is recorded = 6.25 in.
m = the class interval = 0.5 in.
Percentage of fibers under 2 in. = 39.0 %.
Calculations:
v = 100
(σ/X) = 100 × (1.4/2.6) = 56.47 %.
| where: | ||
| X | = | average fiber length of wool, |
| s | = | standard deviation, and |
| v | = | coefficient of variation. |
1.1 This test method covers the measurement of the average length and length distribution of fibers in wool top, on a mass-biased basis. The method is applicable to all types of fibers in sliver formed from long parallelized fibers.
1.2 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
|
Standard Terminology Relating to Wool |
|
|
Standard Terminology Relating to Textiles |
|
|
Standard Test Method of Sampling and Testing Staple Length of Grease Wool (Withdrawn 2022) |
|
|
Standard Test Method for Fiber Length of Wool in Scoured Wool and in Card Sliver (Withdrawn 2022) |
|
|
Standard Practice for Conditioning and Testing Textiles |
