Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Centrifuge Kerosine Equivalent (Withdrawn 2018)
Automaticky preložený názov:
Štandardná skúšobná metóda pre Centrifúga kerozínu ekvivalentu
NORMA vydaná dňa 1.12.2010
Označenie normy: ASTM D5148-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2010
Kód tovaru: NS-30033
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
aggregates, bitumin content, centrifuge kerosine equivalent, surface roughness, &ldquo,k&rdquo, factor, Surface roughness measurement, Bituminous materials/applications, Centrifuge kerosine equivalent, Coarse aggregate, Fine aggregate, Kerosine, ICS Number Code 75.160.20 (Liquid fuels)
Significance and Use | ||||||||||||||||
The CKE furnishes an index, designated as the K factor, that indicates the aggregate particle roughness and surface capacity based on porosity. The CKE is used as part of the Hveem mix design procedure to determine the approximate bitumen ratio (ABR), as shown in Appendix X1. However, there are other applications such as determining the coarse aggregate fraction constant (Kc) for use as an aid in selecting a bitumen content for open-graded friction courses. Note 2—The quality of the results produced by this standard are dependant upon the competence of the personnel performing the procedure and the capability, calibration, and the maintenance of the equipment used. Agencies that meet the criteria of Standard Practice are generally considered capable of competent and objective testing / sampling / inspection / etc. Users of this standard are cautioned that compliance with alone does not completely assure reliable results. Reliable results depend on many factors: following the suggestions of or similar acceptable guideline provides a means of evaluating and controlling some of those factors. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method determines the centrifuge kerosine equivalent (CKE) of aggregate used in bituminous mixtures. 1.2 Units of Measure: 1.2.1 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. An exception is made in the values used for mass because this standard was originally developed using even values of grams, and use of ounces as a standard would make those measures cumbersome. 1.2.2 Regarding sieves, per ASTM Specification E11 Section 1.2, “the values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. The values stated in inchpound units shall be considered standard with regard to the sieve frames.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.1. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Historická
15.4.2012
Historická
1.10.2011
Historická
1.12.2012
Historická
1.5.2014
Historická
1.5.2013
Historická
1.1.2011
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.