Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Preparation of Rock Slabs for Durability Testing
Automaticky preložený názov:
Štandardná prax pre prípravu Skalné Dosky pre dlhú životnosť testovanie
NORMA vydaná dňa 1.7.2010
Označenie normy: ASTM D5121-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2010
Kód tovaru: NS-29918
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
defects, diamond saw blade, durability, rock saw, slabs, Defects, Diamond saw blade, Rock materials/properties/analysis, Rocksaw, Slab/slabs, Specimen preparation (for testing)--rock, ICS Number Code 91.100.15 (Mineral materials and products)
Significance and Use | ||||||||||||
This practice is used to prepare rock specimens for durability testing and to evaluate any internal defects, such as cracks, that may not be apparent on the surfaces of broken blocks of rock. Such evaluation can also aid in the selection and location of slabs for testing as outlined in Practice D4992. In some cases, the need for further testing or evaluation may be eliminated. The sawing of rock samples will reduce them to a suitable specimen size and quantity for testing and, in many cases, preserve the natural structure of the internal defects so the samples can be evaluated by the various durability tests. Durability tests specimens should be 64 ± 6 mm (2.5 ± 0.25 in) thick normal to bedding or any potential planes of weakness which may be observed in the samples. In no case will the size of the slab be less than 125 mm (5 in.) on a side, excluding the thickness Ideally, a test specimen size equal to the proposed design size would provide the ultimate in correlation between laboratory tests and actual field performance. However, in most cases, this is neither practical nor economically feasible. |
||||||||||||
1. Scope | ||||||||||||
1.1 This practice covers the preparation of rock slabs for various tests and any visual inspections used to evaluate the durability of rock for erosion control. These tests include, but are not limited to, Test Methods D5240, D5312, and D5313. 1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.3 All observed and measured values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazards statement, see Section 7. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.